PreSens OXY-1 ST Trace Instruction Manual Download Page 12 | Manualshive

Page: 12 / 14

PreSens OXY-1 ST Trace Instruction Manual Download Page 12

12

OXY-1 ST (Trace)

Operational Notes

© 2017 PreSens Precision Sensing GmbH

5 Operational Notes

5.1 Optical Output

The ST connector is a high precision optical component. Please keep it clean and dry. Always
use the rubber cap to close the output when not in use.

5.2 Maintenance

The transmitter is maintenance-free.
The housing should be cleaned with a cloth only. Avoid any moisture entering the housing.
Never use benzine, acetone, alcohol or any other organic solvents.
The ST fiber connector of the sensor can be cleaned with lint-free cloth or a cleaning
implement for ST connectors only.

5.3 Service

Alignment, rework or repair work may only be carried out by the manufacturer:

PreSens
Precision Sensing GmbH

Am BioPark 11
93053 Regensburg
Germany

Phone +49 941 94272100
Fax

+49 941 94272111

[email protected]
www.PreSens.de

Please contact our service team in case of any question. We look forward to helping you and
are open for any proposition or criticism.

«
...
10
11
12
13
14
»

Summary of Contents for OXY-1 ST Trace















Reviews:

No comments