background image

 

Section 5 - MAINTENANCE 

25 

 

 

© Copyright 2006 PREO SRL 
All rights reserved 

EAW530E2MV 

Edition

03/2006

 

Section 5 

MAINTENANCE 

5.1   MAINTENANCE INFORMATION 

Adequate maintenance is a decisive factor when it comes to keeping your machine 

in good working order for as long as possible, whilst also guaranteeing safety from a 
practical point of view.  
Make sure that maintenance operations are performed by trained personnel 

equipped with personal protection devices, following the safety procedures 
prescribed in the following paragraphs. 
Only use original PREO spare parts, which can be purchased from the company 
sales office. 

Refer to the last section in this manual for a LIST OF RECOMMENDED SPARE 
PARTS. 

5.2   SYSTEM DEPRESSURISATION 

Before disconnecting any plumbing fittings or opening any pressurised parts, make 

sure you follow these procedures in order to discharge the hydraulic pressure that 
could still be present inside the system. 

 

Switch off the motor by turning the switch to position 0 as illustrated in 

figure 23. 

 

Figure 23 

 

Activate the guns until no more adhesive comes out of them. 

5.3   ROUTINE SYSTEM CLEANING 

The machine should be routinely cleaned on a daily basis and at the end of every 
work phase in order to keep the machine in good condition.  

Disconnect the power supply before working on the system, turning the main switch 
to position 0 as illustrated in figure 24. 

Summary of Contents for EASY 5 Series

























































Reviews: