Pagina 2
3. Don not place or store appliance where it can fall or be pulled into a tub or sink. Do not place in or
drop into water or other liquid.
4. Always unplug this appliance from electrical outlet immediately after using. Unplug this appliance
before cleaning, putting on or taking off parts.
WARNING – To reduce the risk of burns, fire, electric shock, or injury to persons:
1. An appliance should never be left unattended when plugged in.
2. Close supervision is necessary when this appliance is used by, on or near children or individuals with
certain disabilities.
3. Use this appliance only for its intended use as described in this manual. Do not use attachments not
recommended by the manufacturer.
4. Never operate this appliance if it has a damaged cord or plug, if it is not working properly, or if it has
been dropped, damaged or immersed in water.
5. Keep the cord away from heated surface.
6. Never drop or insert any object into any opening. Do not use outdoors or operate where aerosol
(spray) products are being used where oxygen is being administered.
7. Do not use this appliance with a damaged cord or broken comb or blade, as cut or scratched skin
may occur.
8. To disconnect, turn all controls to “O”, then remove plug from outlet.
9. Do not wrap the cord around the unit when storing.
10. Avoid contact with moving blades.
11. Avoid tangling or kinking the cord while clipping or trimming.
12. Should the cord become tangled or kinked , stop clipping or trimming and straighten the cord.
13. If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly
qualified persons in order to avoid a hazard.
Operating the Clipper
!
Remove the plastic blade guard covering the teeth of the blades.
!
Push the “O/I” switch to turn the clipper to the “ON” position.
!
When finished clipping, turn the clipper off and unplug from the electrical outlet.
!
Clean the hair clippings from the blades using the clipper brush or an old toothbrush. Wipe the
housing with a clean, dry cloth.
Storage
Replace the blade guard. Coil the electric cord and secure with a twist fastener. Store clipper in a dry
location.
Maintenance
The motor of your clipper has been permanently lubricated at the factory. Other than the recommended
cleaning, oiling of the blades and blade replacement, all maintenance must be performed by repair
service personnel. If the cord becomes twisted, untwist prior to use. If cleaning becomes necessary,
disconnect the exterior with a damp cloth.
Power Screw Instruction
The power screw is available on the right side of the clipper. It permits you to adjust the cutting power.
This screw was adjusted before leaving the factory. However, if the cutting performance is not perfect or
the unit becomes too noisy, you may need to re-adjust it. To adjust while running, use a screwdriver or a
Pagina 3
thin coin to turn clockwise direction until the noise level increases, to minimize the noise, slowly turn the
power screw counterclockwise. This is the maximum power setting.
Blade Adjust – Adjustable clipper
Not all clippers have an adjustable blade. If you have a deluxe adjustable clipper, the following
instructions apply to your clipper. The adjustable clipper has a blade that enables you to cut hair at
various lengths without attachments. To adjust, use thumb adjustment lever to move lower blade up for
FINE cutting and down for COARSE cutting. Fine setting cuts hair very short for neck, etc. coarse setting
leaves hair longer for sideburns, etc. clipper may be adjusted while running. Attachments may be used
with the adjustable clipper by following the guide attachment instructions.
Guide Attachments
To attach your new comb attachments to clipper, be sure to get the front edge of the blade started in the
track of comb. When slipping on combs, use your blade guard over the teeth of the comb. Press palm of
hand against blade guard and push comb into blade. If there is resistance, place a drop of oil on inner
side of comb. If blade guard is not available, precaution should be taken when pressing palm of hand
against comb.
Circuit Diagram
