background image

SPI-EXT

Installation Instructions 

Visit the Premier Mounts website at http://www.mounts.com

 

Page 3

Parts List

Installation Tools

The following tools may be required depending upon your particular installation. They are not included.

Make sure your Premier Mounts product has the following hardware and components before beginning installation. If 

there are parts missing and/or damaged, stop the installation and call Premier Mounts at (800) 368-9700.

Pencil

Protective Eyewear

⅛˝ Wood Drill Bit

Electronic Stud Finder

Phillips Tip Screwdriver

Hand Held Drill

Masonry Drill Bit

Ladder

SpiroLock™ Projector Plate 

(Qty 1)

SpiroLock™ With Extension Mount Hardware

SpiroLock™ Ceiling Plate With Extension 

(Qty 1)

Mounting Legs 

(Qty 4)

#14 x 2˝ Wood Screws 

(Qty 2)

M5 Security Allen Wrench  

(Qty 1)

M3 Flat Washer  

(Qty 10)

M3 x 16mm Security Screw  

(Qty 4)

M6 x 12mm Security Screw  

(Qty 8)

¼-20 x 5/16˝ Security Screw 

(Qty 1)

Lock-It™ Security

Barrel (Qty 1)

M2.5 x 10mm Security Screw  

(Qty 4)

M2.5 x 12mm Security Screw   

(Qty 4)

M4 x 10mm Security 

Screw (Qty 4)

M4 x 12mm Security Screw  

(Qty 4)

M5 x 12mm 

Security Screw 

(Qty 4)

Summary of Contents for SpiroLock SPI-EXT

















Reviews: