background image

 

 

Disclaimer 

 
PREMAS Preventive Maintenance Service AG, hereinafter referred to as PREMAS AG, makes no 
representations or warranties with regard to this manual and limits its liability for the breach of any 
implied warranty to the replacement of this manual by another to the extent permitted by law. In 
addition, PREMAS AG reserves the right to revise this publication at any time without having to 
notify anybody about this revision. 
 
The information provided in this documentation includes general descriptions and/or technical 
characteristics for the performance of the devices. This documentation cannot be considered a 
proper evaluation of the suitability of or reliability of the equipment for a specific application by a 
user and may not be used as a substitute for such an assessment. It lies in the responsibility of each 
such user or installer, to provide an appropriate and complete risk assessment, evaluation and 
testing of the devices for each specific application. Neither PREMAS AG nor any of its partners or 
subsidiaries may be liable for any misuse of the information contained herein. 
 
All relevant state, regional and local safety regulations must always be observed when installing and 
using this device. For reasons of security and to ensure compliance with the documented system 
data, the manufacturer alone is entitled to carry out repairs on components. Failure to observe this 
information may result in injury or damage to the equipment. 
 
Copyright © 2020 PREMAS Preventive Maintenance Service AG  
 
All rights reserved. No part of this publication may be reproduced in any form, including photocopy, 
recording or any other electronic or mechanical reproduced, processed or used in any other way 
without the written permission of the publisher be passed on. Requests for permits must be 
submitted in writing to the publisher and can be sent to the address below. 
 
PREMAS Preventive Maintenance Service AG 

 Haldenstrasse 1 

 6340 Baar 

• Switzerland

 

+41 41 766 82 01 

 

[email protected] 

• 

www.premas.ch

  

 

 

Summary of Contents for 4.0













































Reviews: