page 42
The M9.55 treadmill requires little maintenance to keep it running smoothly and
efficiently. However, you are responsible for typical maintenance tasks such as,
cleaning the unit to keep it free from dust and dirt accumulation. If you fail to maintain
the treadmill as described below, it could affect or void the Precor limited warranty.
Cleaning the Equipment
DANGER — T
O
REDUCE
THE
RISK
OF
ELECTRICAL
SHOCK
,
ALWAYS
UNPLUG
THE
UNIT
FROM
ITS
POWER
SOURCE
BEFORE
CLEANING
IT
OR
PERFORMING
ANY
MAINTENANCE
TASKS
.
Most of the working mechanisms are protected inside the treadmill’s hood and solid
base. However, for efficient operation, the treadmill relies on low friction. To keep the
friction low, the treadmill must be as clean as possible.
Before or after each workout, use a damp, soft cloth to clean the staging platform,
running bed and between the belt and running bed surface as far as you can easily
reach. This removes any dust or dirt which might affect the smooth operation of the unit.
Periodically, clean the treadmill’s frame, display console, handrails and running belt
with a dampened (not dripping wet),
clean cloth using a solution of mild soap and
water. To clean the groves on the belt, use a soft nylon scrub brush. Vacuum the floor
underneath the unit every week to prevent the accumulation of dust and dirt.
The Precor Heart Rate equipment requires little maintenance beyond keeping it dust
free. Dampen a sponge or soft cloth in mild soap and water to clean the POLAR
®
chest strap. Dry the surface thoroughly with a clean towel.
Aligning the Running Belt
The correct alignment of the running belt is critical to the smooth operation of the
treadmill. The belt is properly aligned at the factory. However, during shipping and
handling or by use on an uneven surface, the belt may move off center and require a
few simple adjustments.
Before aligning the running belt, check its operation by following the procedure in
Checking the Alignment of the Running Belt on page 18. If you determine that the
belt needs alignment, follow the instructions here.
Realigning the belt takes a few simple adjustments. If you are unsure about this
procedure, call Precor Customer Support (see
Obtaining Service on page 9.)
Take the following steps to align the running belt on the treadmill. To ensure your
safety, make all adjustments while the treadmill is OFF.
1.
Make sure the treadmill is OFF and the running belt has completely stopped.
2.
Locate the left belt adjustment bolt in the rear end cap of the treadmill. (To
determine left and right, stand at the rear of the treadmill and face the display.)
The direction you turn the bolt depends on how the belt is tracking. Make all belt
adjustments on the
left rear corner bolt using the hex key provided.
•
If the belt is off center to the LEFT, turn the adjusting bolt 1/4 turn clockwise,
which moves the running belt to the right.
•
If the belt tracks off center to the RIGHT, turn the bolt 1/4 turn
counterclock-
wise; this moves the belt to the left.
Important: Do not turn the adjusting bolt more than 1/4 turn at a time.
Overtightening the bolt can damage the treadmill.
Maintaining the Treadmill
8
CAUTION: Never pour water or spray
liquids on the display console, handrails,
or treadmill. Allow the treadmill to dry
completely before using.
CAUTION: Special care must be taken
when aligning the running belt. Turn OFF
the treadmill while adjusting or working
near the rear roller. Remove any loose
clothing and tie back your hair. Be very
careful to keep your finger or any other
object clear of the belt and rollers,
especially in front of the roller and behind
the deck. The treadmill will not stop
immediately if an object becomes caught
in the belt or rollers.
CAUTION: Turn OFF the treadmill and
diconnect the power cord before perform-
ing most maintenance tasks.
Summary of Contents for M9.55
Page 1: ...page 1 Owner s Manual Low Impact Treadmill...
Page 8: ...page 8 Notes...
