manualshive.com logo in svg

Precor C532i, Service Manual, Page: 57 / 70

Share
Download
Precor C532i Service Manual Download Page 57

C532i, C556i Navy Elliptical Fitness Crosstrainer

Page 57

Procedure 7.15 - Replacing a Ramp Assembly

Warning: Care must be taken when work is being performed in the area of the stairarms. Pinch 

points exist between the stairarm and ramp and between the stairarm and crankarm, 
when the rear covers are removed.

1.

Pedal the EFX and press the QUICK START key, while striding on the unit raise the incline 
to its maximum position.

2.

Remove the access panel, top, right and left rear covers per Procedure 7.1

3.

Remove both stairarms per Procedure 7.14.

4.

Remove the two bolts that fasten the lower rear portion of the ramp to the frame. See 
Diagram 7.11.

Diagram 7.11 - Lower Ramp Mounting

5.

Remove the two bolts that fasten the upper end of the ramp to the lift motor yoke. See 
Diagram 7.12.

6.

Carefully lift the ramp and slide it off of the lift motor yoke.

7.

Slide the replacement ramp onto the lift motor yoke and hand. Hand start the two lower 
ramp mounting bolts removed in step 5. Fasten the upper end of the ramp to the lift motor 
yoke with the hardware removed in step 6. Install and torque the two lower ramp bolts to 480 
inch pounds (40 foot pounds).

Lower Ramp

Mounting Bolt

Summary of Contents for C532i







































































Reviews:

No comments