manualshive.com logo in svg

Precor C532i, Service Manual, Page: 10 / 70

Share
Download
Precor C532i Service Manual Download Page 10

C532i, C556i Navy Elliptical Fitness Crosstrainer

Page 10

12. Press the CANCEL (C532i) key to proceed to the Metrics board SW display or the BACK 

key (C556i Navy) to proceed to the serial number display, skip to step.16.

13. The display name “METRICS BOARD SW PART NUMBER will be displayed, press the OK 

key, the metrics board software part number will be displayed.

14. Press the CANCEL (C532i) or the BACK (C556i Navy) key to proceed to the serial number 

display.

15. The display name “SERIAL NUMBER” will be displayed, press the OK key, the serial 

number will be displayed. If the serial number is not present it can be uploaded per 
Procedure 2.5.

16. Press the CANCEL (C532i) or the BACK key (C556i Navy) key to proceed to the usage log 

display.

17. The display name “USAGE LOG” will be displayed, press the OK key.

18. The program used and the time the program was used will be displayed.

19. The keys 

, 

 will scroll you through the list of programs that have been used.

20. Press the CANCEL (C532i) or the BACK (C556i Navy) key to proceed to the error log 

display.

21. The display name “ERROR LOG” will be displayed,  press the OK key.

22. The first error log entry will be displayed “1: ERXX  XX STRIDES XX HRS”.

23. Pressing the 

, 

 keys will move you through the log entries. Press the OK key to view the 

selected error. Entry 1 will be the most recent error log entry, with each succeeding entry 
being older than the preceding entry.

24. If the error log is empty “NO ERRORS” will be displayed.

25. Pressing and holding the QUICK START key for 2 seconds will cause the prompt CLEAR? 

to be displayed, holding the QUICK START for an additional 2 seconds will clear all existing 
entries from the error log. The display will confirm that the error log has been cleared by 
displaying OK. The display will revert to the first log entry and show it as a null entry (1: ---). 
If the QUICK START key is not held for a minimum of 4 seconds, the error log will not be 
cleared.

26. Press the RESET key to exit the diagnostics display program.

Summary of Contents for C532i







































































Reviews:

No comments