background image

PD6700 Field-Mount Loop-Powered Process Meter 

Instruction Manual 

 

11

 

Main Menu Display Functions & 
Messages 

The meter displays various functions and messages 
during setup, programming, and operation. The 
following table shows the main menu functions and 
messages in the order they appear in the menu. 

 

Display 

Parameter 

Action/Setting 

SETUP

 

Setup 

Enter 

Setup

 menu 

DeC..pt 

Decimal point 

Enter 

Decimal Point 

menu 

PRog 

Program 

Enter the 

Program

 

menu 

sCalE 

Scale 

Enter the 

Scale

 menu 

Cal 

Calibrate 

Enter the 

Calibrate

 

menu 

Inpt1 

Input 1 

Calibrate input 1 signal 
or program input 1 value 

DspL1 

Display 1 

Program display 1 value 

Inpt2 

Input 2 

Calibrate input 2 signal 
or program input 2 value 

DsPl2 

Display 2 

Program display 2 value 

Span 

Error

 

Span 
Error 

Error, calibration not 
successful, check signal 

tag 

Tag/Units 

Enter the Tag/Units 
Menu 

ON 

Tag On 

Enable Tag/Units 

OFF 

Tag Off 

Disable Tag/Units 

PASSWRD 

Password 

Enter the 

Password

 

menu 

UNLOCKD

 

Unlocked 

Program password to 
lock meter 

LOCKED

 

Locked 

Enter password to 
unlock meter 

99999 
-99999 

Flashing 
display 

Overrange condition 
Underrange condition 

SERVICE

 

Service 

Select before 
removing/installing 
cover for service or to 
clean the window 

Main Menu 

The main menu consists of the most commonly used 
functions: 

Setup, Password, 

and 

Service

Press 

MENU

 button to enter Programming Mode then 

press the 

Up

 

Arrow

 button to scroll through the main 

menu. 

 

 

Press 

MENU

, at any time, to exit and return to 

Run Mode. Changes made to settings prior to 
pressing 

Enter 

are not saved. 

 

Changes to the settings are saved to memory 
only after pressing 

Enter

 

The display moves to the next menu every time a 
setting is accepted by pressing 

Enter

 

Setting Up the Meter (

SETUP

Press the 

Enter

 button to access any menu or press 

Up

 arrow button to scroll through choices. Press the 

Menu

 button to exit at any time. 

 

 

 
 

Summary of Contents for vantageview Safe Touch PD6700























Reviews: