PRECISION DIGITAL PD2-6300 Instruction Manual Download Page 35

Page: 35 / 59

PD2-6300

Helios Large Display Pulse Input Rate/Totalizer Instruction Manual

Setting the Relay Action

Operation of the relays is programmed in the

Action

menu. The relays may be set up for

any of the following modes of operation:

1. Automatic reset (non-latching)

2. Aut manual reset at any time (non-latching)

3. Latching (manual reset only, at any time)

4. Latching with Clear (manual reset only after alarm condition has cleared)

5. Pump alternation control (automatic reset only)

6. Sampling (the relay is activated for a user-specified time)

7. Off (relay state controlled by Interlock feature)

The following graphic shows relay 1 action setup; relay 2-8 are set up in a similar

fashion.

Programming Set and Reset Points

High alarm indication: program set point above reset point.
Low alarm indication: program set point below reset point.
The deadband is determined by the difference between set and reset points. Minimum

deadband is one display count. If the set and reset points are programmed with the

same value, the relay will reset one count below the set point.

Note: Changes are not saved until the reset point has been accepted.

Setting Fail-Safe Operation

In fail-safe mode of operation, the relay coil is energized when the process variable is within safe limits

and the relay coil is de-energized when the alarm condition exists. The fail-safe operation is set

independently for each relay. Select

to enable or select

off

to disable fail-safe operation.

Programming Time Delay

The

and

Off

time delays may be programmed for each relay between 0 and 999.9 seconds. The

relays will transfer only after the condition has been maintained for the corresponding time delay.
The

time delay is associated with the set point.

The

Off

time delay is associated with the reset point.

www.

.com

[email protected]

1.800.561.8187

Summary of Contents for PD2-6300




























































Search results

Summary of Contents for PD2-6300

Reviews:

Related manuals for PD2-6300

Brands by name

Popular brands

PRECISION DIGITAL PD2-6300, Instruction Manual

Search results

Summary of Contents for PD2-6300

Reviews:

Related manuals for PD2-6300

Brands by name

Popular brands