background image

Transportation

 and storage of compressor 

15 

Transportation and storage of compressor 

Packaging 

Before shipment for storage or before transportation for a long-distance, pack compressor in the original packaging, es-
pecially when moving at a distance: 

 

More that 10 m 

 

over uneven surfaces. 

To do this, perform the following preparatory actions: 

 

Follow the actions described on page 

14

 "After operation". 

 

Clean the connections for compressed air supply from foreign bodies and dirt. 

 

Pack compressor in the original packaging. 

Transportation 

Type of transportation varies depending on the compressor moves for short or long distances. 

Transportation for short distances 

Short distances it is maximum 10 m 

 

Follow the actions described on page 

14

 "After operation". 

Transportation for long distances  

The following distances are long for the compressor transportation: 

 

distances more than 10 m, 

 

distances over uneven surfaces and 

 

moving in unusual position 

 

Transportation of compressor over long distances is allowed only in the original box. 

For transportation of compressor over long distances, proceed as follows: 

 

Follow the actions described on page 

14

 "After operation". 

 

Pack the compressor in the original box in which it was delivered. 

 

Move to the necessary place of work in its original packaging, holding the two holes for lifting. 

 

Place the original box just straight the lid up. 

Storage 

 

Lubricate all metal parts of the compressor with a thin layer of special oil Prebena. 

 

Pack the compressor in the original box. 

 

Store the compressor at room temperature in a dry and dust-free place. 

ATTENTION!

 

Shocks or strikes can damage the compressor. 

 

Avoid dropping the compressor. 

 

Avoid striking the compressor on the obstacles. 

 

Move the compressor taking it at the handle to a new place of work. 

 

Connect the edge device to the compressor only at the new place of work. 

 

Summary of Contents for VITAS 45

























Reviews: