PRAXSYM PAMS User Manual Download Page 10

Page 9 

Initializing Shield Level Measurements 

In Shield Level mode the signal level measured by the receiver must 

be initialized to the test signal from the transmitter to indicated 0 dB 

shield level when the enclosure is open.  This initialization process is 
completed by depressing the CAL button.  Details of the initialization 

process are detailed in the “Making Shield Level measurements” 

section of the manual, section 3.3.   
 

Backlight 

Depress the LIGHT button on the top of the receiver to toggle the 

LCD backlight on/off.  Although the screen will have lower visibility, 

by turning the backlight off the battery life will be increased by 
approximately 10%. 

 

Control Lock 

Once set, the controls of the receiver can be locked to prevent 
inadvertently changing a setting that could result in measurement 

errors.  Depress the LOCK button on the top of the receiver to toggle 

the lock feature on/off.  

 

 

3.2 Transmitter 

The transmitter is a continuous wave signal source with adjustable 
output transmit level over it’s frequency range.   

 
Initial Set-Up and Power On 



Attach one of the antennas to the BNC connector located on the 
top face of the transmitter. 



Power On / rotate POWER switch to ON position. 



Allow a 5 minute warm-up period before making measurements. 

 
  

 

 
 

 

Summary of Contents for PAMS





















Reviews: