manualshive.com logo in svg

PRASTEL MT10000-4, Manual

Share
Download
PRASTEL MT10000-4 Manual Download Page 21

MT4000-2  MT10000-4

 

 

ISMTUK_06_06.doc 

 

 

 

 

 

Pag. 21

6.  Control Unit Firmware Upgrading 

Control unit firmware may be upgraded by means of the TTD3000Pro programme. 
Upgrades are available at Prastel’s web site, www.prastel.it. 

 

Connect control unit connector DB9  to a PC serial port, using the cable provided. 
Access the TTD3000Pro programme and select the serial port to which the control unit has been connected. 

 

 

 

Upgrades always require a Flash file and sometimes an EEprom file, as well.  
Press the “Flash file” (

) key and select the most updated version of the MTFlash.hex file. 

In the event of the upgrade calling for an EEprom file as well, press the “EEprom file” (

) key and 

select the most updated version of the MTEEprom.hex file. 
Press the “Program on reset” (

) key. 

 

 

 

The programme is now ready for upgrade transmission to the control unit. Press the RESET key (card top left-
hand corner) of the control unit to proceed. 
A beep will be heard and the following messages will appear on the control unit display (optional): 

 

 
 
 
 
 
 
The upgraded firmware has at this point been downloaded and after a few seconds the control unit picks up 
again and is ready to operate. 

Upgrading Flash 

… 

Completed OK 

Wait… 

Summary of Contents for MT10000-4


























Reviews:

No comments

Brands by name

Popular brands

Load more brands