background image

 
 
 

CAUTION 

 

This product contains Ultraviolet Light Emitting Diodes (LED’s).  During operation, the 
LED’s emit intense ultraviolet light.  Precautions should be taken to avoid looking directly 
into the UV output for prolonged periods with the unaided eye, viewing the UV output at close 
range, or viewing through optical systems which enhance or concentrate the UV light.  The 
use of UV light protective glasses is recommended when the direct or  reflected UV output 
must be viewed for extended periods,  at close range, or through optics.   
 

DO NOT VIEW DIRECTLY WITH

OPTICAL INSTRUMENTS.

LED RADIATION

CLASS 1M LED PRODUCT

 

 
Controls and Connections  

 
The rear panel of the unit includes a power input jack for a UL approved Class II 24 volt DC power 
source, a red LED power indicator, and three rotary selector switches to choose the base DMX 
address for the device.  A slide switch to the left of the address switches can be set to  provide a 
resistive termination to the DMX data lines if the unit is the last device in the DMX data string.  A 
green LED DMX sync indicator is located to the left of the termination switch to provide a positive 
indication of DMX data reception, and to confirm the mode setting of the unit on power up.  The 
DMX input and output connections are located on the lower half of the unit, to the left of the power 
input socket.    
 
Control Panel Connections 

 

 
 
 

Summary of Contents for BL-48













Reviews: