background image

Version: 1.0

   11 

Cable Routing

7

• 

Avoid wrapping the cables around the pole. 

Route the antenna cables straight down the 

inside of the pole to avoid using extra equipment 

such as cable ties.

• 

Use the minimum cable length required. Do 

not run more cable than needed to ensure 

minimum cable losses are achieved.

• 

Never pull on the cable connectors; pull only 

on the cable ensuring the cable is not under 

tension.

• 

The allowable cable bend radius is 30mm.

• 

Cover connector with insulation tape before 

threading them through a hole.

Safety 

8

• 

If  you  are  installing  an  antenna  for  the  first 

time or unsure about how to install your 

antenna, obtain the help of a professional 

installer.

•  Carefully survey the installation site before 

installation to locate secure handholds, 

dangerous conditions (such as power 

lines and weak roofs) and the safest and 

most convenient placement for ladders if 

necessary.

When installing your antenna, remember:

1.  Do not install near power lines as they can 

electrocute you.

2.  Do not install on a wet or windy day or when 

lightning or thunder is in the area.

3.  Wear shoes with rubber soles and heels 

and protective clothing (long sleeve shirt or 

jacket) and rubber gloves.

4. 

Avoid operating while under the influence of 

drugs, alcohol or medication.

5. 

Make  sure  that  any  loose  fitting  jewelry  or 

clothing is secured and tie back long hair as 

they can get caught in moving parts during 

installation.

6.  If the antenna starts to fall, step away to 

avoid harm.

Summary of Contents for MIMO-3-V2













Reviews: