Powtran PR5200 Series Manual Download Page 3 | Manualshive

Page: 3 / 36

background image

Precaution



Thanks for selecting intelligent motor soft starter products from Powtran technology Co.,
LTD., we will with excellent performance in return for your attention!



Please pay attention to the following matters during the soft starter installation, operation
and maintenance process

Please be sure to read the operating instructions before installation

Must by professional technicians to install the soft starter

The specifications of the motor must match with the soft starter

Prohibit to connect the capacitors in soft starter output terminal (U, V, W)

The bare terminals must be wrapped by insulating tape after installation

Soft starter or related equipment should be reliable grounding

Input power must be cut off when equipment maintenance

Do not disassemble , modify, maintenance of this product personally.

Only trained people are allowed to operate this device, please read this

manual about the safety, installation, operation, and maintenance section before
use of the items. The safe application of this equipment depends on the correct
transportation, installation,operation and maintenance.

«
1
2
3
4
5
...
»

Summary of Contents for PR5200 Series





































Reviews:

No comments

Related manuals for PR5200 Series

Brand: Wavelink Pages: 69

Brand: Jabra Pages: 4

Brand: Securi-Prod Pages: 3

Brand: AirCycler Pages: 2

Torque Converter Lock-Up

Brand: TS Performance Pages: 4

Brand: Danfoss Pages: 8

TITAN-TRACKSIDE-3

Brand: Remote Control Systems Pages: 4

Brand: Consort Pages: 4

Brand: Hach Pages: 48

Brand: Niko Pages: 28

Brand: Shaw Pages: 44

Brand: M-system Pages: 7

Brand: Smarthome Pages: 12

easy2read Lepton3x1

Brand: Caen RFID Pages: 31

Brand: BABY MONSTERS Pages: 29

Brand: Danfoss Pages: 22

SmartLoop KTSL-FC1-UV-KO

Brand: Keystone Pages: 2

Brand: Hanwha Techwin Pages: 5

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands