PowerTec MT4006 Owner'S Manual Download Page 3

SAFETY RULES

1

1

SAFETY RULES

     WARNING

For your own safety, read all of the rules and precautions 
before operating tool.

     WARNING

Always follow proper operating procedures as defined 
in this manual even if you are familiar with the use of 
this work bench or any tool used with this work bench. 
Remember that being careless for even a fraction of a 
second can result in severe personal injury. 
You must be familiar with the use of any tool or accessory 
used with this work bench. The supplier cannot be held 
responsible for any accident, injury or damage incurred 
while using this work bench with any tool.

     WARNING

Some dust created by operation of power tool contains 
chemicals known to the State of California to cause  
cancer, birth defects or other reproductive harm. To 
reduce your exposure to these chemicals, work in a well 
ventilated area and work with approved safety equipment. 
Always wear OSHA/NIOSH approved, properly fitting face 
mask or respirator when using such tools.

     CAUTION

Do not modify or use this work bench for any application 
other than that for which it was designed.

SAFETY FOR WORK BENCH

•  Do not attempt to assemble or operate your work bench 

until you have read the safety instructions in this section.

•  Only use your work bench on a hard, dry and 

flat surface.

•  Keep your work area clean and well lit. Cluttered or dark 

areas invite accidents.

•  Do not overreach. Keep proper footing and balance at 

all times.

•  Do not load the work bench with more than 220 lbs 

(100 kg).

•  Do not stand on the work bench. Do not use the work 

bench as a ladder or standing platform.

•  Do not stand or climb on work bench. It could tip over, 

causing serious injury.

•  Make sure the legs are opened fully and locked in place 

before using the work bench.

•  Be aware of tipping. Make sure the load is balanced, an 

unbalanced load can tip. Always ensure the workpiece 
is well supported.

•  Do not permit children to use the work bench 

unsupervised. It is not a toy.

•  Dress properly. Do not wear loose clothing or jewelry. 

Keep your hair, clothing and gloves away from moving 
parts. Loose clothes, jewelry or long hair can be caught 
in moving parts. Always wear non-slip footwear. Tie 
back long hair. Roll long sleeves above the elbow.

•  Store properly. Do not store the work bench outdoors or 

in a damp location.

     CAUTION

Think safety! Safety is a combination of operator common 
sense and alertness at all times when tool is being used.

     WARNING

Do not attempt to operate tool until it is completely 
assembled according to the instructions.

SAVE ALL WARNINGS AND INSTRUCTIONS  

FOR FUTURE REFERENCE

Summary of Contents for MT4006









Reviews: