background image

 

11 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

 
 

19

 

 

Fuel Tank Cap

 

 

 

 

 

20

 

 

 

 

 

 

Choke Lever

 

 
Drive Control Lever 

Located on the right side of the upper handle, the Drive Control Handle is used to engage and disengage 
the drive wheels. Squeeze the Drive Control Handle against the upper handle to engage the wheels; 
release to disengage. 
 

Drive Speed/Gear Control  

The Speed/Gear Control is located on the center of the panel and is used to set the drive speed and 
direction of travel. It can be moved into any of six positions (four forward and two reverse gear settings) 
 

Auger Control Lever 

Located on the left side of the upper handle, the Auger Control Handle is used to engage and disengage 
the augers. Squeeze the Auger Control Handle to engage the augers; release to disengage the augers. 
 

Chute Rotation Handle 

To adjust snow discharge direction, rotate the handle clockwise or counter-clockwise….should rotate 
180 degrees. 
 

Skid Shoe 

Position the shoes based on the surface conditions. Adjust upward for hard-packed snow. Adjust 
downward when operating on gravel or crushed rock surfaces. 
 

Auger Blade and Impeller 

When engaged, the auger blades rotate to cut snow and direct it into the auger/impeller housing to be 
discharged out the chute. 
 

Clean-out Tool 

The chute Clean-out Tool is conveniently fastened to the rear of the auger housing with a mounting clip. 
It is used to clean the chute assembly and chute opening when snow and ice become lodged. 

WARNING!

 Never use your hands to clear a clogged chute assembly. Shut off engine and remain behind 

handles until all moving parts have stopped before unclogging. 

 

19

 

20       

 

Summary of Contents for DB7651BS-24

































Reviews: