background image

 

POWE50102 

EN

 

Copyright © 2018 VARO 

P a g e

 | 

9

 

www.varo.com 

9.11 

Sawing  

Make  sure  the  saw  blade  doesn’t  block  while  you  are  sawing.  It  causes 
damage to and burning of the motor. If there is a blockade of the saw blade, 
please loosen the switch immediately to prevent damage at the motor. 

 

Clamp the work piece firmly. 

 

Set the required horizontal mitre angle or the required vertical bevel angle. 

 

Switch on the power tool. 

 

Move the handle (3) slowly downwards. You have to push the safety switch (2) before you 
can do this. 

 

Saw trough the work piece. 

 

Switch off the power tool. 

 

Wait until the saw blade (13) has come to a complete standstill before removing the work 
piece. 

9.12 

Sawing special work pieces 

Curved or round work pieces need to be secured against slipping. 
Make sure there is no gap between the work piece and the fence (6) or the saw table (8). 

9.13 

Replacing the saw blade (Fig. 2) 

Disconnect the tool from the outlet before working on the saw blade.  

Wait a while before touching the saw blade. It can be very hot. 

The teeth of the saw blade are very sharp. 

 

Allow the mitre saw cutting head to rise to the upright position 

 

Loosen the cover plate screw (2) with a allen key. 

 

Tilt the cover plate (3) upwards in order to make the axle bolt (4) accessible. 

 

Press the spindle lock button, holding it in firmly while turning the blade wrench clockwise. 
The spindle lock will engage after turning the wrench. Continue to hold the spindle lock 
button to keep it engaged, while turning the wrench clockwise to loosen the spindle bolt. 

 

Remove the spindle bolt, the blade collar and the blade. Do not remove the inner blade 
collar. 

 

Replace the saw blade (the tips of the sawing teeth have to point in the same direction as 
indicated by the arrow on the cover) and then reassemble all parts in the reverse order. 

 

Turn the plastic cover back in its original position. 

10 CLEANING AND MAINTENANCE 

Before performing any work on the equipment, pull the power plug. 

10.1 

Cleaning 

 

Regularly clean the machine housing with a soft cloth, preferably after each use. 

 

If the dirt does not come off use a soft cloth moistened with soapy water. 

 

Never use solvents such as petrol, alcohol, ammonia water, etc. These solvents may 
damage the plastic parts. 

Make sure no water can reach the inside of the power tool! 

 

 

Summary of Contents for POWE50102













Reviews: