manualshive.com logo in svg

Powermatic 1150HD, Instruction Manual

Share
Download
Powermatic 1150HD Instruction Manual Download Page 8

8

TABLE                      BASE

SPECIFICATIONS  

  1150A Drill Press

Spindle ................................................... steel, 10-spline, #33 Jacobs Taper with 0"-1/2" capacity chuck

Spindle Travel ......................................................................................................................................... 6"

Quill Diameter ................................................................................................................................. 2-3/16"

Column Outside Diameter ...................................................................................................................... 3"

Column Wall Thickness ..................................................................................................................... 3/16"

Column Length, Floor Model ................................................................................................................ 66"

Column Length, Bench Model .............................................................................................................. 42"

Table Working Surface:

Tilting Table ......................................................................................................................... 10" x 14"

Production Table .................................................................................................................. 12" x 18"

Base Working Surface ............................................................................................................. 8-1/2" x 12"

Drilling Capacity (Cast Iron) ................................................................................................................. 5/8"

Tapping Capacity (Cast Iron) ............................................................................................................... 1/2"

Drilling Capacity (Steel) ....................................................................................................................... 1/2"

Tapping Capacity (Steel) ...................................................................................................................... 3/8"

Throat Depth ...................................................................................................... Drills to center of 15" dia.

Spindle Nose to:

Floor Model - Production Table             37-1/4"                  47-1/4"

Floor Model - Tilting Table                          41"                  46-1/4"

Key Chuck to:

Floor Model - Production Table             36-3/4"                 47-1/4"

Floor Model - Tilting Table                    40-1/2"                        46"

T-slots use Standard T-Bolts ............................................................................................................... 1/2"

Spindle Speeds:

Variable Speed Models

1800 RPM Motor .................................................................................................. 450-4800 RPM

1200 RPM Motor .................................................................................................. 300-3200 RPM

Step Pulley Models

1800 RPM Motor ......................................................................... 400-840-1580-2800-5300 RPM

1200 RPM Motor ......................................................................... 260-560-1050-1875-3550 RPM

Shipping Weight ............................................................................................................................ 323 lbs.

Summary of Contents for 1150HD













































Reviews:

No comments

Brands by name

Popular brands

Load more brands