Powermate CX6500E Owner'S Manual Download Page 8

6

Owner’s Manual for Portable Generator

Connection Plugs

120 VAC, 20 Amp, GFCI Duplex 
Receptacle

The 120 Volt outlet is overload protected by a

20 Amp push-to-reset circuit breaker. See 

Fig-

ure 2-4

. Each receptacle will power 120 Volt

AC, single phase, 60 Hz electrical loads

requiring up to 2400 watts (2.4 kW) or 20

Amps of current. Use only high quality, well-

insulated, 3-wire grounded cord sets rated for

125 Volts at 20 Amps (or greater).

NOTE: 

Limit length of extension cords to fif-

teen feet, or less, to prevent voltage drop and

overheating of wires.

Figure 2-4. 120 VAC, 20 Amp, GFCI Duplex 

Receptacle NEMA 5-20R

120/240 VAC, 30 Amp Receptacle

Use a NEMA L14-30 plug with this receptacle

(rotate to lock/unlock). Connect a suitable 4-

wire grounded cord set to plug and desired

load. The cord set should be rated 250 Volts

AC at 30 Amps (or greater). See 

Figure 2-5

.

CX6500E:

 Use this receptacle to operate

120 Volt AC, 60 Hz, single phase loads

requiring up to 3240 Watts (3.2 kW) of

power at 27 Amps or 240 Volt AC, 60 Hz,

single phase loads requiring up to 6480

watts (6.4 kW) of power at 27 Amps. The

outlet is protected by two 27 Amp 2-pole

connected toggle circuit breakers.

CX8000E:

 Use this receptacle to operate

120 Volt AC, 60 Hz, single phase loads

requiring up to 3600 watts (3.6 kW) of

power at 30 Amps or 240 Volt AC, 60 Hz,

single phase loads requiring up to 7200

watts (7.2 kW) of power at 30 Amps. The

outlet is protected by two 30 Amp push-to-

reset circuit breakers.

Figure 2-5. 120/240 VAC, 30 Amp Receptacle 

NEMA L14-30R

120 VAC, 30 Amp Receptacle

Use a NEMA L5-30 plug with this receptacle

(rotate to lock/unlock). Connect a suitable 3-

wire cord set to the plug and to desired load.

The cord set should be rated for 125 Volts AC

at 30 Amps (or greater). See 

Figure 2-6

.

Use this receptacle to operate 120 Volt AC,

60Hz, single phase loads requiring up to 3600

watts (3.6kW) of power at 30 Amps. The outlet

is protected by a 30 Amp push-to-reset circuit

breaker.

Figure 2-6. 120 VAC, 30 Amp Receptacle 

NEMA L5-30

Remove Contents from Carton

1. Open carton completely by cutting each

corner from top to bottom.

2. Remove and verify carton contents prior to

assembly. Carton contents should contain

the following:

000203

000204

000844

Summary of Contents for CX6500E

























Reviews: