background image

www.powerbox-systems.com

11

ver damage caused by incorrect usage, e.g. reverse polarity, excessive vibra-

tion, excessive voltage, damp, fuel, short-circuits, etc. The same applies to 

defects due to severe wear. We accept no liability for transit damage or loss 

of your shipment. If you wish to make a claim under guarantee, please send 

the device to the following address, together with proof of purchase and a 

description of the defect:

SERVICE ADDRESS

PowerBox-Systems GmbH

Ludwig-Auer-Straße 5

D-86609 Donauwoerth

Germany

11. LIABILITY EXCLUSION

We are not in a position to ensure that you observe our instructions regarding 

installation of 

PowerPaks

, fulfil the recommended conditions when using the 

unit, or maintain the entire radio control system competently. For this reason 

we deny liability for loss, damage or costs which arise due to the use or opera-

tion of 

PowerPaks

, or which are connected with such use in any way. Regard-

less of the legal arguments employed, our obligation to pay compensation is 

limited to the invoice total of our products which were involved in the event, 

insofar as this is deemed legally permissible.

We wish you every success with your new 

PowerPak

.

Donauwoerth, March 2019

Summary of Contents for PowerPak 2.5X2 ECO













Reviews: