13
4111-0068 — Oct. 2018
© 2018 Systems, LLC
INSTALLATION
Put New Barrier Into Service
1. Remove pipe plug from filler port on hydraulic fluid
reservoir and replace with breather cap provided.
2. Check hydraulic fluid level and add as necessary.
See page 18 for required fluid level and type.
3. Turn on power to barrier control panel.
4. If necessary, use control panel to extend lifting
cylinder rod. Connect lifting cylinder (
A
) rod to barrier
arm (
B
) by sliding cylinder pin (
C
) through the barrier
arm, cylinder rod and spacer (
D
), then secure with rue
clip (
E
). Grease barrier arm pivot pin at pivot tube (
F
).
See Figures 8 and 9.
Note:
If rear sheet metal cover was removed from
main body during install, reinstall it at this time.
5. Operate barrier up and down several times to
ensure proper location of barrier receiver weldment.
6. Once positioned properly with double gusset
(single anchor) side towards wall, use the barrier
receiver weldment as a template and drill three (3)
holes for concrete anchors (5/8” x 5” min.).
Note:
If the floor is not square with respect to the
mounting plates, metal shims should be inserted to
prevent the plates from twisting during lagging to the
floor.
7. Position the barrier receiver weldment as needed
and install three (3) 5/8” x 5” min. concrete anchors.
8. Test system to verify proper operation:
• Amber light should be off when barrier arm is in
the horizontal position (barrier in use) and in the
vertical position (barrier stored).
• Pressing the raise button should cause the barrier
arm to raise smoothly; releasing the raise button
should stop barrier arm motion.
• Pressing the lower button should cause the barrier
arm to lower smoothly; releasing the lower button
should stop barrier arm motion.
TOLERANCES
(UNLESS OTHERWISE NOTED)
FRACTIONAL:
1/32"
DECIMAL:
.00 =
.01"
.000 =
.005"
ANGULAR:
1
DRAWN BY
CHECKED BY
DRAWING NO.
DATE
BDK
10/3/2018
S Y S T E M S
L o a d i n g D o c k E q u i p m e n t
P O W E R A M P
M C G U I R E
D L M
This print is the property of Systems, LLC and represents a proprietary article in which Systems, LLC retains any and all patent and other rights, including exclusive rights
of use and/or manufacture and/or sale. Possession of this print does not convey any permission to reproduce, print or manufacture the article or articles shown therein,
such permission to be granted only by written authorization signed by an officer or other authorized agent of Systems, LLC thereof.
MATERIAL
STOCK NO.
B2 BARRIER
ASSEMBLY
REV A - ECN 18-066
TOLERANCES
(UNLESS OTHERWISE NOTED)
FRACTIONAL:
1/32"
DECIMAL:
.00 =
.01"
.000 =
.005"
ANGULAR:
1
DRAWN BY
CHECKED BY
DRAWING NO.
DATE
BDK
10/3/2018
S Y S T E M S
L o a d i n g D o c k E q u i p m e n t
P O W E R A M P
M C G U I R E
D L M
This print is the property of Systems, LLC and represents a proprietary article in which Systems, LLC retains any and all patent and other rights, including exclusive rights
of use and/or manufacture and/or sale. Possession of this print does not convey any permission to reproduce, print or manufacture the article or articles shown therein,
such permission to be granted only by written authorization signed by an officer or other authorized agent of Systems, LLC thereof.
MATERIAL
STOCK NO.
B2 BARRIER
ASSEMBLY
REV A - ECN 18-066
A — Lift Cylinder
B — Barrier Arm
C — Cylinder Pin
D — Spacer
E — Rue Clip
F — Pivot Pin Grease Fitting
Figure 8
Figure 9
C
A
B
E
D
F