background image

30

TM

IMPORTANT!

Use only Power Wheels

®

12 volt battery.

Use of any other battery will damage your vehicle. Make
sure that you charge the battery for at least 18 hours using
the enclosed Power Wheels

®

12 volt charger 

before

operating your vehicle for the first time.

Charge the

battery for at least 14 hours after each use of the vehicle.
Never charge the battery longer than 30 hours. Failure to
follow these instructions may damage your battery and will
void your warranty.

TM

• Remove the seat. Press the tab at the back of the seat

and lift.

• Place the Power Wheels

®

12 volt battery upright in the

battery compartment.

Make sure the battery terminals

face the rear of the vehicle.

• Fit the battery clamp over the battery.

• Insert a screw through each end of the battery clamp

and into the screw pegs in the vehicle body.

• Tighten the screws using a Phillips screwdriver.

Do not over-tighten.

TM

• Plug the motor harness connector into the battery.

Push firmly to make sure the connector is secure in
the battery.

• Replace the seat on the vehicle.

Vehicle

Body

Power Wheels

®

12 Volt Battery

Battery

Compartment

Battery Installation

Battery Clamp

Screw

Peg

Screw

Peg

Battery

Motor

Harness

Connector

H

1

2

3

Summary of Contents for B3160









































Reviews: