background image

Picture  

 

Description 

Decal Location

1.

  

A. 1

5kg Maximum load 

Inside toolbox, front face

2.

  

A.

   Do not tie down over guardrails 

Each side of cage, middle and lower guardrail

  

B.

 

Product logo, x 2 

Left hand and right hand side of platform tray

3. 

  

A.

   234 kg Max wheel/castor load, x 4 

Left and right hand side of chassis - 2 each side, position 

 

 

 

 

appropriate label according to wheel/label colour

  

Note: Use 245 kg Max wheel/castor load for Wind Rated machine. (Labels are on same sheet).

  

B.

  Fork lift point x 2 

Left and right hand side - 1 each side centre of    

 

 

 

 

 

chassis between forklift loading pockets

4.

  

A.

 

Spirit Level Guidance 

Left hand side of spirit level, on chassis cover

5.

  

A.

 

Emergency lowering procedure 

Chassis cover, left hand side of mast

  

B.

  Do not enter the area underneath 

Centre of chassis cover, front of mast

 

 

 

a raised platform unless it is supported

6.

  

A.

  Hand trap point 

Chassis, directly opposite bottom of mast

  

B.

  Lifting/tie down point x 2 

Each corner of chassis next to lifting/tie down points 

 

7.

  

A.

   Operating Instructions 

Left hand gate, upper panel.

 

B.  

Use advisory label 

Right hand gate, upper panel

 

C.

  

150kg SWL

 

Left hand gate, lower panel

8. 

A.

  Horizontal pull force max 200 N 

Middle of mast, internal face

 

B.

  Safety Guidelines 

Middle of mast, internal face

 

C. 

Harness point, fall restraint only 

Middle of mast, internal face

DECAL PLACEMENT

20

Courtesy of Crane.Market 

Summary of Contents for EcoLift





























Reviews: