Power smart DB7651A- 26 User Manual Download Page 4

3

• Exercise caution to avoid slipping or falling, 

especially when operating in reverse.

• Stay alert, watch what you are doing and use 

common sense when operating your Snow Thrower. 

• Do not use your Snow Thrower while you are tired 

or under the influence of drugs, alcohol, medication. 
A moment of inattention while operating the Snow 
Thrower may result in severe bodily injury.

• NEVER LEAVE YOUR RUNNING SNOW 

THROWER UNATTENDED. Stop the engine. 

• Do leave your Snow Thrower until it has come to a 

complete stop.

• When stepping backwards, be cautious about any 

obstacles beneath your feet or behind you avoid 
falling.

Service

• Stop the engine before making any adjustments. 

Check for misalignment, breakage of or binding of 
moving parts, and any other conditions that may 
affect operation.

• If damaged, have the Snow Thrower serviced by a 

qualified repair person using only identical 
replacement parts. This will ensure that the safety of 
the Snow Thrower is maintained.

Safe handling of gasoline

To avoid personal injury or property damage use 
extreme care in handling gasoline. Gasoline is 
extremely flammable and the vapors are 
explosive. Serious personal injury can occur 
when gasoline is spilled on yourself or your 
clothes which can ignite, wash your skin and 
change clothes immediately.

• Use only an approved gasoline container.
• Extinguish all cigarettes, cigars, pipes and other 

sources of ignition.

• Never fuel machine indoors.
• Never remove gas cap or add fuel while the engine 

is hot or running.

• Allow engine to cool at least two minutes before 

refueling.

• Never over fill fuel tank.Fill fuel to no more than 1/2 

inch below bottom of filler neck to provide space for 
fuel expansion.

• Replace gasoline cap and tighten securely.
• If gasoline is spilled, wipe it off the engine and 

equipment. Move machine to another area. Wait 5 
minutes before starting the engine.

• Never store the machine or fuel container inside 

where there is an open flame, spark or pilot light 
(e.g. furnace, water heats, space heater, clothes 
dryer etc.).

• Allow machine to cool at least 5 minutes before 

storing.

• Never fill containers inside a vehicle or on a truck or 

trailer bed with a plastic liner. Always place 
containers on the ground away from your vehicle 
before filling.

• If possible, remove gas-powered equipment from 

the truck or trailer and refuel it on the ground.

• If this is not possible, then refuel such equipment on 

a trailer with a portable container, rather than from a 
gasoline dispenser nozzle.

• Keep the nozzle in contact with the rim of the fuel 

tank or container opening at all times until fueling is 
complete. Do not use a nozzle lock open device.

Operation

• Do not put hands or feet near rotating parts, in the 

auger impeller housing or chute assembly. Contact 
with the rotating parts can amputate hands and feet.

• The auger impeller control lever is a safety device. 

Never bypass its operation. Doing so makes the 
machine unsafe and may cause personal injury.

• The control levers must operate easily in both 

directions and automatically return to the 
disengaged position when released.

• Never operate with a missing or damaged chute 

assembly. Keep all safety devices in place and 
working.

• Never run an engine indoors or in a poorly 

ventilated area. Engine exhaust contains carbon 
monoxide, an odorless and deadly gas,

• Do not operate machine while under the influence of 

alcohol or drugs.

• Muffler and engine become hot and can cause a 

bum. Do not touch. Keep children away.

• Exercise extreme caution when operating on or 

crossing gravel surfaces. Stay alert for hidden 
hazards or traffic.

• Exercise caution when changing direction and while 

operating on slopes.

• Plan your snow-throwing pattern to avoid discharge 

towards windows, walls, cars etc. Thus, avoiding 
possible property damage or personal injury caused 
by a ricochet.

• Never direct discharge at children, bystanders and 

pets or allow anyone in front of the machine.

• Do not overload machine capacity by attempting to 

clear snow at too fast of a rate.

• Never operate this machine without good visibility or 

light. Always be sure of your footing and keep a firm 
hold on the handles. Walk, never run.

• Disengage power to the auger impeller when 

transporting or not in use.

• Never operate machine at high transport speeds on 

slippery surfaces. Look down and behind and use 
care when backing up.

Summary of Contents for DB7651A- 26


























Reviews: