background image

14

Chain saw lubrication test

Control the chain to operate towards 

one dry surface and accelerate the 

throttle to operate at half speed for 

about 30s.
Check whether a clear oil line can be 

seen on the dry surface.

Chain brake

Check of braking performance of brake

1. Place the chain saw on the ground.

2.  Control the handle with both hands

to accelerate the engine to high

speed.

3.  Trigger the front baffle by rotating

the left wrist holding the front baffle,

so as to enable the chain brake.

4. The chain is stopped immediately.

5. Loosen the throttle.

Release of chain brake

The chain brake is released when the 

front baffle completely returns to the 

operator side.
If the chain cannot be stopped 

immediately, send the chain saw to 

POWERKING 

for maintenance.

Warning  

  Danger

Most of risks are caused by bounce of the guide plate, 

while bounce is caused when the top of the guide plate 

is subject to collision against wood or similar objects.
The chain brake can be used to reduce or avoid physical 

injury caused by bounce of the guide plate.
Check the effectiveness of the chain brake before using 

the chain saw each time.

Non-artificial invention of chain brake

The tail end of the guide 

plate must be kept 35cm 

above the plane.

35cm

Hold the rear handle 

with the right hand.

Non-artificial invention of the chain brake means that the chain 

brake is stopped as a result of bounce of the tail end of the guide 

plate. In order to ensure the normal action of the chain brake 

free from artificial invention, take the following test steps.

1)

Stop the engine of the chain saw.

2)

Carefully control the front and rear handle by hand until

the tail end of the guide plate is 35cm high, as shown in

the above figure.

3)

Carefully rotate the left hand holding the front handle until

the front part or top of the guide plate hits the wood or

similar objects under the chain saw. In this case, the chain

saw is subject to impact (do not hold the rear handle too

tightly with the right hand).

4)

The impact will be transferred to the front baffle to

activate the chain brake.

Attention

To exercise the operation, press the front baffle 

forwards to activate the brake in the process of 

cutting small trees. If the chain brake is stuck in wood 

chippings, the functions of the chain brake will be 

weakened. Always keep the system clean.

Do not check the chain brake in the place with 

gasoline mist.

Chain braking 

direction

Direction of 

release of 

chain brake

Summary of Contents for PK4516




























Reviews: