DANGER:
• Double insulated tools are equipped with a polarized
plug (one blade is wider than the other). This plug will
fit in a polarized outlet only one way. If the plug does not
fit fully in the outlet, reverse the plug. If it still does not
fit, contact a qualified electrician to install a polarized
outlet. Do not change the plug in any way. Double
insulation eliminates the need for the three wire
grounded power cord and grounded power supply
system.
SPECIFIC SAFETY RULES
1. Hold tool by insulated gripping surfaces when
performing an operation where the cutting tool may
contact hidden wiring.
Contact with a "live" wire will
also make exposed metal parts of the tool "live" and
shock the operator.
SYMBOLS
The following symbols are used for the tool:
V ............ Volts
Amp ........ Amperes
~ ............. Alternating Current
............ Double Insulted
HZ ........... Hertz
RPM ........ Revolutions Per Minute
........... Drill Mode
........... Hammer Mode
WARNING
• Dust and debris created during drilling, grinding or
sanding on some materials may contain chemicals
known to the State of California to cause cancer or birth
defects or other reproductive harm. To reduce exposure
to these chemicals, always use approved safety
equipment, work in a well-ventilated area and wear
dusk mask that filters out microscopic particles.
FUNCTIONAL
DESCRIPTION
B
C
L
D
F
E
K
G
A
A
1/2" Chuck
B
Drill / Hammer Drill Selector Lever
C
Variable Speed Trigger
D
Trigger Lock Button
E
Chuck Key
F
Chuck Key Holder
G
Support Handle
H Auxiliary
Depth Gauge Clamp Handle
I
Depth Gauge Mount
J Auxiliary
Handle Clamp Screw
K
Depth Gauge
L
Forward / Reverse Selector Lever
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
I
J
1. On / Off Switch
2. Trigger Lock Button
3. Forward / Reverse Lever
1
2
3
1. To start the drill, pull the trigger (1). Rotational speed
will increases as the trigger is depressed. To stop,
release the trigger.
2. For continuous operation, pull the trigger (1) and
depress the lock-on button (2). The drill will continue to
run until the trigger is pulled fully and then released.
Caution:
• Do not move the forward and reverse lever (3) while
drill is in use, damage to tool could result. Allow tool to
come to a complete stop before changing direction.
• Always check tool rotation direction before drilling.
3. Use the forward and reverse lever (3) to select direction.
Push it to the left "L" position for counter clockwise
rotation and right "R" position for clockwise rotation.
Variable Speed Trigger
(Figure 2)
Figure 4
1. Installing / Changing Bits
WARNING:
• RISK OF PERSONAL INJURY. ALWAYS DISCONNECT
TOOL FROM POWER SOURCE BEFORE MAKING ANY
ADJUSTMENT, INSTALLING OR CHANGING ACCESSORIES
Caution:
• Always remove chuck key before connecting tool to
power source.
1. Rotate ring (1) counterclockwise to open chuck.
2. Insert drill bit shank into chuck as far as it will go.
3. Insert chuck key (2) into hole and rotate clockwise to
tighten or counter clockwise to loosen. Apply
downward pressure on the chuck key to ensure proper
engagement of the gears.
1
2
Installing / Changing Bits
(Figure 4)
1
1. Speed Limiting Knob
1. To limit the maximum rotational speed of the drill
when the trigger is full depressed use the speed limit
knob (1).
2. Rotate the knob in the "+" clockwise direction to
increase maximum speed and in the "-" counter
clockwise direction to reduce maximum speed.
Caution:
• Do not force the speed limiting knob beyond its range
Damage to the tool could result.
• Do not use the tool at low speed settings for
prolonged periods. Overheating may occur.
Speed Limiting Knob (Figure 3)
2
Forward / Reverse Lever (Figure 2)
H
1. Rotate the drill / hammer drill selector knob to the
" " position for drill rotation only.
2. Rotate the drill / hammer drill selector knob to the
" " position for drill rotation with hammering.
DRILL / HAMMER DRILL SELECTION
(Figure 4)
1. Drill / Hammer Drill Selector
1
FIGURE 4
FIGURE 3
FIGURE 2
Caution:
• Do not move the drill/hammer drill selector lever (1)
while tool is in us. Damage to tool could result. Allow
tool to come to a complete stop before changing mode.
