background image

2

Power-Flo Pumps & Systems • 877-24PUMPS • www.powerflopumps.com

PF4NC-SS   

 

 

 

 

 

 

 

 

      Non-Clog Pumps

General Safety Information

® Power-Flo  is a registered trademark of Power-Flo Technologies Inc. Other brand and product names are trademarks or registered trademarks of 

their respective holders. Alteration Rights Reserved. 

3/08, 6/09, 7/10, 2/11, 10/11, 4/13, 9/15, 8/17, 9/2020, 1/2021

Before installation, read the following 
instructions carefully. Failure to follow 
instruction and Safety information could 
cause serious bodily injury, death and/or 
property damage. Each Power-Flo pump is 
individually factory tested to insure proper 
performance. Closely following these 
instructions will eliminate potential operating 
problems, assuring years of trouble-free 
service.

                                           “

Danger” indicates

 

 

        an imminenty 

hazardous situation which, if not avoided, 

WILL result in death or serious injury.

                                                 “Warning” indicates

 

 

        an imminenty 

hazardous situation which, if not avoided, 

MAY result in death or serious injury.

 

 

        “Caution”  indicates

 

 

         an potentially 

hazardous situation which, if not avoided, 

MAY result in minor or moderate injury.

IMPORTANT - Power-Flo Pumps and 

Systems is not responsible for losses, injury 

or death resulting from failure to observe 

these safety precautions, misuse, abuse or 

misapplication of pumps or equipment.

 ALL

 

RETURNED 

 PRODUCTS MUST BE
 CLEANED, SANITIZED,
 OR DECONTAMINATED
 PRIOR TO SHIPMENT, TO 

INSURE EMPLOYEES WILL NOT BE EXPOSED 
TO HEALTH HAZARDS IN HANDLING SAID 
MATERIAL. ALL APPLICABLE LAWS AND 
REGULATIONS SHALL APPLY.

 

 

       Installation, wiring,

 

 

       and junction 

connections must be in accordance with 
the National Electric Code and all applicable 
state and local codes. Requirements may 
vary depending on usage and location.

 

 

        Installation and

 

 

        servicing is to be 

conducted by qualified personnel only.

  

 

        Keep clear of suction

   

       and discharge

 openings. Do not insert fingers in 
 pump with power connected.

 

 

       Always wear eye

 

 

       protection when 

working on pumps. Do not wear loose 
clothing that may become entangled in 
moving parts

 

  

      Pumps build up heat 

  

 

      and pressure during

 operation. Allow time

 for pumps to cool 

 before handling or
 servicing.  

 

 

      This pump is 

not

 

 

      intended for use

 in swimming pools or water 
 installations where human 
 contact with pumped fluid. 

 

 

       Risk of electric shock. 

   

       To reduce risk of 

  electric shock, always disconnect 
  pump from power source before 
  handling. 

Lock out power & tag.

 

 

       Do not us these 

 

 

       pumps in water 

over 104˚F. Do not exceed manufactures 
recommended maximum performance, as 
this could cause the motor to overheat.

 

 

      Do not lift, carry or 

   

      hang pump by the

 electrical cables. Damage to the
 electrical cables can cause shock,
 burnes or death. Never handle 

connected power cords with wet hands. Use 
appropriate lifting device.

 

 

      Sump and sewage 

 

 

      pumps often handle 

materials which could cause illness or disease. 
wear adequate protective clothing when 
working on a used pump or piping. Never 
enter a basin after it has been used.

 

 

      Failure to permanently

 

 

      ground the pump, 

 motor and controls before
 connecting to power can cause
 shock, burns or death.

 

 

        These pumps are NOT

  

        to be installed in

 locations classified as hazardous in
 accordance with the National 
 Electric Code, ANSI/NFPA 70.

   

 

       

 

 

      The Uniform Plumbing

 

 

      Code (UPC) states that

sewage systems shall have an audio and 
visual alarm that signals a malfunction of 
the systems that is required to reduce the 
potential for property damage.

IMPORTANT!

Prior to installation, record Model 

Number, MFG Date, Amps, Voltage, Phase 

and HP, from pump name plate for future 

reference. Also record the Voltage and 

Current Readings at Startup:

1 Phase Models

Amps:

Volts:

3 Phase Models

Amps L1-2:

Volts L1-2:

Amps L2-3:

Volts L2-3:

Amps L3-1:

Volts L3-1:

Model Number: ____________________

MFG Date: ____________

PHASE: ______ HP: _________________

WARNING: 

CANCER AND REPRODUCTIVE HARM-

WWW.P65WARNINGS.CA.GOV

Summary of Contents for PF4NC2824SS Series

























Reviews: