Powercraft
09
6)
Service
a.
Please use a qualified expert who uses original replacement parts to repair your power tool.
This will ensure proper functioning of the power tool.
b.
Caution! The use of any accessories or additional tools other than those recommended in
this manual may lead to an increased risk of injury. Only use original replacement parts.
Important safety notes on charger and batteryblock
If you come into contact with acid from the battery block, rinse it off with water
immediately. If acid gets into your eyes, rinse out your eyes at once with water and
contact a doctor immediately!
1.
Read and note the operating instructions and safety notes for the charger and battery block
before use!
2.
NB! Only use the charger and battery block that were supplied by the manufacturer -
otherwise you will risk an accident.
3.
Protect the charger, battery block and power tool from moisture, e.g. rain or snow.
4.
Always check that all cables are connected correctly before using the charger.
5.
If you discover that a cable is damaged, you should not use the charger again. Have the
damaged cable replaced immediately.
6.
When the charger is not in use, the mains plug should be removed from the power socket.
Do not pull out the plug by grasping the cable.
7.
If the charger has been dropped or has otherwise been exposed to high mechanical
stresses, you should have it checked for damage by an authorised dealer before using it
again. Damaged parts should be repaired.
8. Exercise caution when handling the battery block and do not drop it or expose it to impacts.
9.
Never attempt to repair the charger or battery block yourself. Repairs must always be
carried out by an authorised dealer - otherwise you risk an accident.
10. Before cleaning or servicing the charger or battery block, always pull the plug from the
charger socket.
11. Never charge the battery block when the ambient temperature is below 5 °C or above 40°C.
12. The air vents in the charger must never be blocked.
13. The battery block must not be short-circuited.
A short-circuit will cause a high current to flow. This may result in overheating, the
danger of fire or explosion of the battery block. This may damage the battery block
or the user may risk an accident.
Therefore:
•
Do not connect any cables to the poles of the battery block.
•
Take care that there are no metal objects (nails, paper clips, coins, etc.) on the contact
surface of the battery block.
•
Do not expose the battery block to water or rain.
•
Only use the battery block supplied in combination with this cordless drill/screwdriver
so as to avoid faults and/or risks to persons.
14. Adamaged battery block or one that can no longer be charged must be disposed of as
special waste. Do not discard it with household waste.
GB
D
NL
F
E
P
I
S
SF
N
DK
Powercraft
Switching the device on and off
Fig. A
•
Depress the on/off switch (1). It regulates the speed of the appliance by transmitting power
to the switch.
•
Release the on/off switch (1) to halt the drill chuck immediately which will no longer run on.
•
Move the direction reversing switch (6) to the centre in order to lock the appliance in its
disabled state.
Only lay down the appliance when it has stopped running completely. Do not place it on a dusty
surface as particles of dust could get into the mechanism.
Tips
•
Use only bits that fit properly in the head of the screw.
•
When driving in larger and/or longer screws in hard material, it is advisable to drill a pilot
hole first.
•
For drilling in metal, use only perfectly sharpened HSS drills.
Charging the battery
Fig. F + G
The enclosed battery charger has been exclusively designed for loading batteries of the PCC-
1800.
•
Position the battery (5) in the battery charger (11) as indicated in the illustration.
•
Plug in the battery charger. The red “fast charging” light (12) is then illuminated
•
As soon as the green light (13) is illuminated, charging has finished and the accumulator is
ready for use
•
The energy display (14) on the battery gives information about the charge.
Only use the battery charger in a dry environment at a temperature between 5 °C
and 40 °C.
The battery on the drilling machine you have purchased is not charged up. Before using it for the
first time leave it to charge for 1 - 2 hours in order for it to reach its full capacity. The total capacity
of the battery will be reached after it has been charged 4 - 5 times.
If the cordless drill is not going to be used for a long period of time, recharge the
battery before storing. From time to time recharge the battery for a short period of
time, to prevent it from running down. Store the battery separately in the plastic
case.
Discharging the battery
Not only charging batteries is important, discharging is of equal importance or even
greater importance.
12
GB
D
NL
F
E
P
I
S
SF
N
DK
