background image

6

wearing of suitable clothing and
masks.

Always work within Health and
Safety requirements.

Never process media such as
white petroleum spirit, butyl
alcohol and methylene chloride
with the PVC pressure hose
(reduced life span).

Operation of pressure
vessels in accordance
with the pertinent
pressure vessel
regulations 

1. An operator of a pressure 

vessel is required to keep the 
pressure vessel in good 
working order, to operate it 
properly, to supervise its use, 
to carry out essential 
maintenance and repair work 
immediately, and to introduce 
essential safety measures 
according to requirements.

2. The supervisory authorities 

may order essential safeguards
from case to case.

3. A pressure vessel may not be 

operated if it has any defects 
which constitute a danger to 
employees or third parties.

4. The pressure vessel must be 

regularly inspected for damage,
e.g. rust. If you discover any 
damage, then please contact 
the customer service 
workshop.

Putting the compressor
into operation

Assembling the wheels (1):

Fit the wheels as shown in
Figure 1. 

Assembling the rubber buffer

Fit the supplied rubber buffer to
the support foot as shown in
Figure 2.

Replacing the oil filter and
installing the air filter (fig. 3)

Use a screwdriver to remove the
oil filler plug and insert the
supplied stopper (2) in the
opening.
Important! Check the oil level.
Screw the air filter (1) into the
hole in the side of the compressor
pump.

Connecting to the power
supply:

The compressor is equipped with
a power cable and an earthing-pin
plug for connection to any 230 V
~ 50 Hz earthing-contact socket
outlet with a 13 A fuse. Long
supply lines, extensions, cable
reels and similar cause voltage
dips and may prevent the motor
from starting. Sluggishness
makes starting difficult at low
temperatures under freezing

point (0°C).

Explanation of the compressed
air fittings

1 Pressure switch
2 Safety valve
3 Pressure gauge (to indicate the 

vessel pressure)

4 Pressure gauge (to indicate the 

set pressure)

5 Pressure reducing valve 

(pressure setting)

6 On/Off switch

GB

1

2

3

4

 

Anleitung PCC 210-8  16.11.2004  10:55 Uhr  Seite 6

Summary of Contents for 40.072.80















Reviews: