Powell Power/Vac ML-17 Operator'S Manual Download Page 8

Page: 8 / 33

A. S

cope

The information in this instruction bulletin

describes the following Power/Vac

Electrical

Ground and Test Devices

• 50kA and below, using the 49A or 69A

vacuum bottle, equipped with Revision 1

ML-17 operating mechanism

• 63kA using the 68A vacuum bottle,

equipped with Revision 1 ML-17 operating

mechanism

The “Revision 1” mechanism can be identified

by the “1” in the 8th position of the catalog

number as shown on the nameplate,

i.e., GEPVEGT1xxxxxxxxx.

ML-17/49A and ML-17/69A devices include:

• GMV 1050

• GMV 1051

• GMV 1052

• GMV 1053

• GMV 1054

• GMV 1055

• GMV 1060

• GMV 1061

ML-17H/68A devices include:

• EGT-63-A

• EGT-63-B

B. p

urpoSe

The information in this instruction bulletin is

intended to provide information required to

properly operate and maintain the

ground and test device described in

Ch 1 General Information,

A. S

cope

This instruction bulletin provides:

1. Safety guidelines

2. General descriptions of the operation and

maintenance of the ground and test device

3. Instructions for installation and placing the

ground and test device into service

4. Instructions for part replacement

5. Information for ordering renewal parts

6. Procedure for critical adjustments

7. Illustrations, photographs, and description

of the ground and test device

The illustrations contained in this document

may not represent the exact construction

details of each particular type of ground and

test device. The illustrations in this document

are provided as general information to aid in

showing component locations only.

All illustrations and photos are shown using

deenergized equipment.

Be sure to follow the appropriate safety

precaution while handling any of the

equipment. Failure to do so may result in

serious injury or death.

WARNING

To the extent required, the products described

herein meet the applicable ANSI, IEEE, and

NEMA Standards; however, no such assurance

is given with respect to local codes and

ordinances which may vary greatly.

Powered by Safety

General Information

Power/Vac® Electrical Ground and Test Devices

Equipped with ML-17 Mechansim

01.4IB.50100

Summary of Contents for Power/Vac ML-17


































Search results

Summary of Contents for Power/Vac ML-17

Reviews:

Related manuals for Power/Vac ML-17

Brands by name

Popular brands

Powell Power/Vac ML-17, Operator'S Manual

Search results

Summary of Contents for Power/Vac ML-17

Reviews:

Related manuals for Power/Vac ML-17

Brands by name

Popular brands