Powell LVSWGR-AR Manual Download Page 10

Page: 10 / 38

Powered by Safety

General Information

Low Voltage Arc Resistant Switchgear (LVSWGR-AR

)

Equipped with Magnum DS Circuit Breakers

01.4IB.26263B

A. S

cope

The information in this instruction bulletin

describes Powell low voltage arc resistant

metal-enclosed switchgear assemblies

equipped with Magnum DS Low Voltage Power

Circuit Breakers. The equipment described is

indoor type switchgear for applications up to

and including 635 Volts and 4000A.

Standard construction details are provided

in the appropriate sections. The circuit

breaker element operation and maintenance

instructions can be found in the Magnum

DS operating instruction manual provided

with each circuit breaker. Any special

switchgear construction details are provided in

supplementary documentation.

B. p

urpoSe

The information in this instruction bulletin

is intended to provide information required

to properly operate and maintain the low

voltage arc resistant switchgear equipped with

Magnum DS circuit breakers.

This instruction bulletin provides:

1. Safety guidelines

2. General descriptions of the operation

and maintenance of the low voltage arc

resistant switchgear

3. Instructions for installation of the

switchgear

4. Information for ordering renewal parts

5. Illustrations, photographs, and description

of the switchgear. Refer to the Eaton

publication shipped with the device for

circuit breaker information.

The illustrations contained in this document

may not represent the exact construction

details of each particular type of switchgear

section. The illustrations in this document

are provided as general information to aid in

showing component locations only.

All illustrations and photos are shown using

deenergized equipment.

Follow the appropriate safety precautions

while handling any of the equipment. Failure

to do so may result in death or serious injury.

WARNING

To the extent required, the products described

herein meet the applicable ANSI, IEEE, and

NEMA Standards; however, no such assurance

is given with respect to local codes and

ordinances which may vary greatly.

c. I

nStructIon

ulletInS

vAIlABle

lectronIcAlly

Changes to the instruction bulletin may

be implemented at any time and without

notice. Go to powellind.com to ensure use

of the current instruction bulletin for Powell

equipment.

NOTICE

To contact the Powell Service Division call

1.800.480.7273 or 713.944.6900, or email

[email protected].

For specific questions or comments pertaining

to this instruction bulletin email

[email protected] with the

Instruction Bulletin number in the subject line.

Summary of Contents for LVSWGR-AR







































Search results

Summary of Contents for LVSWGR-AR

Reviews:

Related manuals for LVSWGR-AR

Brands by name

Popular brands

Powell LVSWGR-AR, Manual

Search results

Summary of Contents for LVSWGR-AR

Reviews:

Related manuals for LVSWGR-AR

Brands by name

Popular brands