Poulan Pro PZ4822 Operator'S Manual Download | Manualshive

Page: 44 / 75

background image

English-

43

MAINTENANCE

Deck belt installation

NOTE: For ease in installing the deck belt,
refer to the routing decal on bottom of seat.

•

Wrap the deck belt around the electric
clutch pulley that is located on the engine
shaft.

•

Route the belt forward between the EZT
(E-Series Zeroturn Transaxles) and up
onto the deck.

•

Place belt around spring loaded

idler

pulley, between the pulley and guide.
Secure bolt and nut.

•

Starting on the right hand side of the
deck, wrap the belt around the stationary
idler pulley, the right mandrel housing,
then around to the left mandrel housing.

•

Push inward on the idler arm and
carefully route belt over stationary idler
pulley. Once belt is properly routed,
slowly release idler arm to tension belt.

•

Double check belt routing to make sure it
matches the routing decal, and the belt
does not have any twist. Correct as
needed.

•

Replace belt shields on both mandrel

housings and secure with fasteners.

1

1. Clutch pulley

Belt routing, deck belt

«
...
42
43
44
45
46
...
»

Summary of Contents for PZ4822












































































Reviews:

No comments

Related manuals for PZ4822

Camm-1 CX-24/12

Brand: Roland Pages: 20

Brand: Zenoah Pages: 32

Donut Depositor N Series

Brand: Belshaw Brothers Pages: 25

Brand: Mafell Pages: 174

Brand: Milwaukee Pages: 16

Brand: Hitachi Koki Pages: 32

Brand: Makita Pages: 8

Brand: Fellowes Pages: 20

Brand: Fellowes Pages: 28

Brand: Solo Pages: 100

Brand: LEITZ Pages: 30

Brand: Perfecta Pages: 32

Brand: sunjoe Pages: 16

Brand: US Cutter Pages: 42

Brand: WBT Pages: 16

Brand: Cub Cadet Pages: 24

Brand: Zenoah Pages: 42

Brand: Garland Pages: 144

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands