background image

23

KEY    PART            
NO.     NO.                DESCRIPTION

NOTE:

  All component dimensions given in U.S. inches.

 1 inch = 25.4 mm

1         180677           Transmission Assembly  

(In-

 cludes Key Nos. 2-53)

2         180627           Gearcase, L.H. w/Bearing   (In-

 cludes Key No. 4)

3         161963           Gasket, Gearcase
4         5020J             Bearing, Needle
5         1370H            Washer, Thrust  5/8 x 1.10 x 1/32
6         137335           Pinion, Input
7         145101           Shaft, In put
8         4895H            Bearing, Needle
9         154467           Washer, Seal
10       7392M            Ball, Steel
11       100371K        Spring, Shift, Fork
12       106160X        O-Ring
13       142145           Arm, Shift
14       8353J             Fork, Shift
15       12000039       Ring, Klip
16       154466           Shaft, Shift
18       4358J             Washer
19       12000040       Ring, Klip
20       102114X        Gear, As sem bly, Reverse Idler (In-

cludes Key Nos. 21 and 22)

21       102115X        Gear, Re verse Idler
22       6803J             Bearing, Needle
23       102111X        Shaft, Re verse Idler

REPAIR PARTS

TILLER - - MODEL NUMBER PRRT65B

TRANSMISSION

KEY    PART            
NO.     NO.                DESCRIPTION

24       10040700       Washer, Lock  7/16
25       73610700       Nut, Hex  7/16-20
27       143009           Bearing, Shaft, Ground Drive L.H.
28       106390X        Spacer  0.765 x 1.125 x 1.23
29       102134X        Chain  #35-50 Pitch
30       150737           Ground Shaft Assembly
31       143008           Bearing, Shaft, Ground Drive R.H.
32       106388X        Spacer  0.70 x 1.00 x 1.150
33       102121X        Sprocket and Gear Assembly
34       102112X        Shaft, Re duc tion (2nd)
35       102101X        Screw, Whiz, Lock  5/16-18 x 3-1/2
36       154355           Sprocket Assembly w/Bearing (In-

cludes Key Nos. 37 and 38)

37       4422J             Bearing, Needle
38       154356           Sprocket, Tine
39       105345X        Gear, Clus ter, Red 1st & 2nd
40       105346X        Gear, Re verse
41       8358J             Shaft, Re duc tion (1st)
42       4220R            Washer, Thrust
43       106146X        Spacer  1.01 x 1.75 x 0.760
44       155236           Seal Asm, Oil
48       180631           Gearcase, R.H. w/Bearing   (In-

 cludes Key No. 8)

49       132688           Shaft, Tine
50       106147X        Chain, Roller  #50-50 Pitch
51       17720408       Screw  1/4-20 x 1/2
52       73220500       Nut, Hex  5/16-18
53       165140           Kit, Bearing
58       179520           Bolt Shoulder
60       6855M            Fitting Grease
- -        6066J             Grease, Plastilube #1

Summary of Contents for PRRT65B





























Reviews: