manualshive.com logo in svg

Poulan Pro Pro 925 ZX, Pro 950 ZX, Operator'S Manual

Share
Download
Poulan Pro Pro 925 ZX, Pro 950 ZX Operator'S Manual Download Page 45

English-

43

MAINTENANCE

Deck belt installation

NOTE: For ease in installing the deck belt, 
refer to the routing decal on bottom of seat.

•

Wrap the deck belt around the electric 
clutch pulley that is located on the engine 
shaft.

•

Route the belt forward between the EZT 
(E-Series Zeroturn Transaxles) and up 
onto the deck.

•

Place belt around spring loaded

 

idler 

pulley, between the pulley and guide. 
Secure bolt and nut.

•

Starting on the right hand side of the 
deck, wrap the belt around the stationary 
idler pulley, the right mandrel housing, 
then around to the left mandrel housing.

•

Push inward on the idler arm and 
carefully route belt over stationary idler 
pulley. Once belt is properly routed, 
slowly release idler arm to tension belt.

•

Double check belt routing to make sure it 
matches the routing decal, and the belt 
does not have any twist. Correct as 
needed.

•

Replace belt shields on both mandrel

 

housings and secure with fasteners.

1

1. Clutch pulley

Belt routing, deck belt

Summary of Contents for Pro 925 ZX, Pro 950 ZX

















































































Reviews:

No comments

Brands by name

Popular brands

Load more brands