Poulan Pro Pro 925 ZX, Pro 950 ZX Operator'S Manual Download Page 35

Page: 35 / 80

English-

OPERATION

Moving by Hand

When pushing or pulling the mower, be sure
to engage the EZT (Integraded Zeroturn
Transaxle) bypass linkages. The EZT bypass
linkages are located on the rear of the frame.

•

Raise the deck into the highest cutting
position.

•

Pull the EZT bypass linkages out and
into the slots and release so that it is held
in the bypass position.

•

To reengage the EZT’s to drive, reverse
the above procedure.

Load machine into truck or trailer by driving
up ramps in low gear. DO NOT LIFT! This
machine is not intended to be lifted by hand.

8011-721

1. EZT Bypass linkages

Bypass linkages

8011-722

1. Head outside of rear deck

2. EZT Bypass linkage in bypass position

Bypass position

Summary of Contents for Pro 925 ZX, Pro 950 ZX

















































































Search results

Summary of Contents for Pro 925 ZX, Pro 950 ZX

Reviews:

Brands by name

Popular brands

Poulan Pro Pro 925 ZX, Pro 950 ZX, Operator'S Manual

Search results

Summary of Contents for Pro 925 ZX, Pro 950 ZX

Reviews:

Brands by name

Popular brands