background image

4

CONGRATULATIONS 

on your purchase of a new tiller. It 

has been designed, en gi neered and manu fac tured to give 

you the best pos sible de penda bil ity and per form ance.
Should you experience any prob lems you can not easily 

remedy, please contact your nearest authorized service 

center.  We have com pe tent, well-trained tech ni cians and 

the proper tools to service or repair this unit.
Please read and retain this manual. The in struc tions will 

enable you to assemble and main tain your tiller prop erly. 

Always observe the “SAFETY RULES”.

CUSTOMER RESPONSIBILITIES

•  Read and observe the safety rules.
•  Follow a regular schedule in maintaining, caring for 

and using your tiller.

•  Follow instructions under “Maintenance” and “Stor age” 

sections of this Owner’s Manual.

IMPORTANT:  

THIS UNIT IS EQUIPPED WITH AN INTERNAL 

COMBUSTION ENGINE AND SHOULD NOT BE USED ON 

OR NEAR ANY UNIMPROVED FOREST-COVERED, BRUSH-

COVERED OR GRASS COVERED LAND UNLESS THE ENGINE'S 

EXHAUST SYSTEM IS EQUIPPED WITH A SPARK ARRESTER 

MEETING APPLICABLE LOCAL LAWS (IF ANY).  IF A SPARK 

ARRESTER IS USED, IT SHOULD BE MAINTAINED IN EFFECTIVE 

WORK ING ORDER BY THE OPERATOR.
IN THE STATE OF CALIFORNIA, A SPARK ARRESTER IS 

REQUIRED BY LAW (SECTION 4442 OF THE CALIFORNIA 

PUBLIC RESOURCES CODE).  OTHER STATES MAY HAVE 

SIMILAR LAWS.  FEDERAL LAWS APPLY ON FEDERAL LANDS.  

SEE YOUR AUTHORIZED SERVICE CENTER/DEPARTMENT  

FOR SPARK ARRESTER.

MAINTENANCE SCHEDULE ...................................13
MAINTENANCE  .................................................13-15
SERVICE & ADJUSTMENTS ..............................16-18
STORAGE ................................................................19
TROUBLESHOOTING ..............................................20

TABLE OF CONTENTS

SAFETY RULES ......................................................2-3
CUSTOMER RESPONSIBILITIES .............................4
PRODUCT SPECIFICATIONS ...................................4
ASSEMBLY ..............................................................5-7
OPERATION ..........................................................8-12

PRODUCT SPECIFICATIONS

 GASOLINE CAPACITY: 

1.47 Quarts (1,4 L) 

 

 

 

 Unleaded Reg u lar

 OIL (API SJ–SN): 

SAE 30 (Above 32°F/0°C) 

   

(Capacity: 16 oz./0,47L) 

SAE 5W-30 (Below 32°F/0°C)

 SPARK PLUG : 

NGK BPR6ES   

 

(GAP:  .010"/0.25mm) 

TORCH F6RTC

SUPPORT / HELP

If you require assistance or have questions concerning the application, operation, maintenance or parts for your product:

 

•  Visit our website:  www.poulanpro.com
•  Call Us Toll Free: 1-800-849-1297

Summary of Contents for PPCRT14









































Reviews: