background image

27

REPAIR PARTS

 

SNOW THROWER - MODEL  

PO11TEPH30

  (96198000500)

DRIVE

NOTE:  All component dimensions given in U.S. inches.     1 inch = 25.4 mm

IMPORTANT:  Use only Original Equipment Manufacturer (O.E.M.) replacement parts.

Failure to do so could be hazardous, damage your snow thrower and void your warranty.

KEY   PART                
NO.    NO.                    DESCRIPTION

   1    198584            Screw, Hex Head  5/16-18 x 1/2
   2    187794            Spacer, Axle
   3    174697            Washer, Thrust
   4    74780632        Screw, Cap, Hex Head  3/8-16 x 2
   5    179830            Bearing, Axle
   6    73800600        Nut, Hex, Centerlock  3/8-16
   7    187776            Transmission Assembly
   8    187787            Speed Control Arm, Hydro
   9    700279            Retainer Clip

10    188101            Torque Strap

 11    193255X479    Bracket, Anti-Rotate

12    73800400        Nut, Hex, Nylock  1/4-20
13    150078            Screw, Hex Washer Head  5/16-18 x 3/4
14    193256            Rod, Bypass Valve
15    191995            Pop Rivet
16    404308            Shaft, Axle
18    198466            Cable, Drive Control
19    192000            Bracket, Cable, Rear
20    191993            Bracket, Cable, Front
21    87930              Clip, Cable
22    17391208        Screw, Slotted Hex Head  1/8 x 1/2
23    146315            Screw, Hex Head  5/16-18 x 3/4

Summary of Contents for PO11TEPH30

































Reviews: