background image

29

REPAIR PARTS

 

SNOW THROWER - MODEL  

PP10530ES

  (96192001803)

CHASSIS / ENGINE / PULLEYS

NOTE:

  All component dimensions given in U.S. inches.     1 inch = 25.4 mm

IMPORTANT:

  Use only Original Equipment Manufacturer (O.E.M.) replacement parts.

Failure to do so could be hazardous, damage your snow thrower and void your warranty.

KEY   PART 

NO.    NO. 

DESCRIPTION

 1 

181044

 

 Spring, Traction Idler

  2  180522 

 Pulley, Idler (2-1/4)

  3     - - -  

 Engine, Tecumseh, Model Number 

     

 LH358SA (For engine service and re-

placement parts, call Tecumseh Prod-

ucts at 1-800-558-5402)

  4  74780520 

 Screw, Hex Head  5/16-18 x 1-1/4

 6  59289 

 Washer, Flat

  7  166785 

 Nut, Jam, Lock  5/16-18

  8  175330 

 Pin, Idler Pivot

  9  407908 

 V-Belt, Traction Drive

 10  10040500 

 Washer, Lock  5/16

 11  17490508 

 Screw, Hex Washer Head

5/16-18 x 1/2

 12  410420 

 Impeller Arm Assembly

 13  85179 

 Retainer, Hairpin

 14  178828 

 Spring, Brake

 15  408007 

 V-Belt, Impeller Drive

 16  150406 

 Screw, Hex Head  3/8-16 x 1-1/4

 17 

179354

  

Arm, 

Idler

 18  74780524 

 Screw, Hex Head  5/16-18 x 1-1/2

 19  175331 

 Bushing, Idler Pivot

 20  180523 

 Pulley, Idler (2-3/4)

 21  74610516 

 Screw, Hex Head  5/16-24 x 1

 22  409475 

 Spacer, Engine Pulley

 23  180478 

 Pulley, Engine, Traction Drive

 24  179157 

 Pulley, Engine, Impeller Drive

 25  400026 

 Washer, Flat  3/8

 26  850263 

 Washer, Lock  3/8

KEY   PART 

NO.    NO. 

DESCRIPTION

 27  851084 

 Screw, Hex Head  3/8-24 x 1-3/8

 28  155452 

 Guide, Belt

 29  192213 

 Belt Cover Assembly

(Includes Toolbox Cover)

 30  178830 

 Cover, Toolbox

 31  17490408 

 Screw, Hex Head  1/4-20 x 1/2

 32  402881 

 Bolt, Shoulder  5/16-18

 33  403096X004   Bellcrank Shifter

 34  198580 

 Clevis Pin

 35  405485 

 Arm, Auger Control

 36  191730 

 Locknut, Hex

 37  402856X004   Plate, Clutch

 38  187101 

 Link, Speed Control

 39  416717X004   Bracket, Clutch

 41  700279 

 Hairpin, Cotter  3/32 x 1/2

 42  73930500 

 Locknut, Hex

 43  403097X004   Plate, Shifter

 44  17000616 

 Screw, Hex Head

 45  175324X479   Pivot Bracket, Impeller Idler Arm

 46  410877 

 Pan, Frame Bottom

 47  184471 

 Screw

 49 

414999X428

  

Frame Assembly

 50 

403215X428

   Plate, Frame End

 51  406109 

 Shaft, Auger Control

 52  57079 

 Washer, Hardened

 53  35062 

 Key, Safety

 57  11050500 

 Washer, Lock, External Tooth

 58  198563 

 Power Cord

Summary of Contents for 96192001803

































Reviews: