background image

27

REPAIR PARTS

 

SNOW THROWER - MODEL  

PP10530ES

  (96192001803)

DRIVE

NOTE:

  All component dimensions given in U.S. inches.     1 inch = 25.4 mm

IMPORTANT:

  Use only Original Equipment Manufacturer (O.E.M.) replacement parts.

Failure to do so could be hazardous, damage your snow thrower and void your warranty.

KEY   PART 

NO.    NO. 

DESCRIPTION

  2  751153 

 Nut, Lock  5/16-18

  4  17490508 

 Screw, Hex Head  5/16-18 x 1/2

 5  180017 

 Bearing, Flange

 6  180134 

 Shaft, Auxiliary

 7  179270 

 Spacer, Plate

 8  192616X479  Plate, Auxiliary

  9  180082 

 Gear, Intermediate (12/58)

 10  180065 

 Gear, Pinion

 11  403300 

 Rod, Clutch

 12  180066 

 Shaft, Long, Hex

 13  178807 

 Pin, Pivot

 14  178619X479   Lever, Shifter / Wheel

 15  175344 

 Trunnion Bearing Assembly

 16 

186951X479

   Bracket, Pivot, Shift

 17  179831 

 Ring, Rubber Wheel

 18  198176X479   Plate, Rubber Wheel

 19  73930500 

 Nut, Lock  5/16-18

 20  178613 

 Hub, Rubber Wheel

 21  74760514 

 Screw, Hex Head  5/16-18 x 7/8

 22  85179 

 Retainer, Hairpin

 23  180135 

 Spring, Bias

 24  180081 

 Gear, Axle (58 Teeth)

 25  178695 

 Pin, Pivot Lever

 26  197763 

 Plate Assembly, Drive

 27  404307 

 Shaft, Axle

 28  197764 

 Shaft, Short Hex

 29  175350X479   Lever, Shifter Plate

 30  175349X479   Bracket, Shifter Support

 31  72270505 

 Bolt, Carriage  5/16-18 x 5/8

 32  189282 

 Key, Square  1/4 x 1/4 x 7/8

 33  188909 

 Bearing, Flange

 34  175338X479   Plate, Drive Mounting

 35  182504 

 Spacer, Bearing

 36  191080 

 Pulley, Traction Drive

 37  155377 

 Nut, Lock  5/16-18

 38  19111507 

 Washer, Flat

 39  10040500 

 Washer, Lock 5/16

 40  74950512 

 Screw, Hex Head  5/16-18 x 3/4

 41  12000012 

 Ring, Retaining

 43  179095 

 Spring, Return

 44  9465MI 

 Pin, Roll

Summary of Contents for 96192001803

































Reviews: