Poulan Pro 545001484 Instruction Manual Download Page 7

Page: 7 / 18

Cutters

Depth Gauge

Drive Links

Place chain onto the sprocket

7. Place chain over and behind clutch, fitting

the drive links in the clutch drum sprocket.

8. Fit bottom of drive links between the

teeth in the sprocket in the nose of the

guide bar.

9. Fit chain drive links into bar groove.

10. Pull guide bar forward until chain is snug

in guide bar groove. Ensure all drive

links are in the bar groove.

NOTE: CHAIN BRAKE MUST BE

DISENGAGED BEFORE INSTALLA-

TION ON THE SAW. TO DISENGAGE

CHAIN BRAKE, PULL THE FRONT

HAND GUARD BACK TOWARD THE

REAR OF THE CHAIN BRAKE AS

FAR AS POSSIBLE (SEE ILLUSTRA-

TION).

DISENGAGED

ENGAGED

Chain Brake

Front Hand Guard

11. Now, install chain brake making sure the

adjusting pin is positioned in the lower

hole in the guide bar. Remember this pin

moves the bar forward and backward as

the screw is turned.

12. Install chain brake nuts and finger tighten

only. Once the chain is tensioned, you

will need to tighten chain brake nuts.

CHAIN TENSION

(Including units with chain already installed)

NOTE:

When adjusting chain tension,

make sure the chain brake nuts are finger

tight only. Attempting to tension the chain

when the chain brake nuts are tight can

cause damage.

Checking the tension:

Use the screwdriver end of the chain adjust-

ment tool (bar tool) to move the chain around

the bar. If the chain does not rotate, it is too

tight. If too loose, the chain will sag below the

bar.

Chain Brake Nuts

Chain Adjustment

Tool (Bar Tool)

Adjusting the tension:

Chain tension is very important. Chain

stretches during use. This is especially true

during the first few times you use your saw.

Always check chain tension each time you

use and refuel your saw.
You can adjust the chain tension by loosen-

ing the chain brake nuts and turning the ad-

justing screw 1/4 of a turn while lifting up on

the bar.

If chain is too tight, turn adjusting screw 1/4

turn counterclockwise.

If chain is too loose, turn adjusting screw

1/4 turn clockwise.

Adjusting

Screw

Chain Brake Nuts

Guide Bar

Adjusting Screw -- 1/4 Turn

Lift up the tip of the bar and securely tight-

en the chain brake nuts with the bar tool.

Recheck chain tension.

Chain Brake

Nuts

WARNING:

If the saw is operated

with a loose chain, the chain could jump off

the guide bar and result in serious injury.

Summary of Contents for 545001484



















Search results

Summary of Contents for 545001484

Reviews:

Related manuals for 545001484

Brands by name

Popular brands

Poulan Pro 545001484, Instruction Manual

Search results

Summary of Contents for 545001484

Reviews:

Related manuals for 545001484

Brands by name

Popular brands