background image

31

REPAIR PARTS

 

SNOW THROWER - MODEL  

PP13TEPH30

  (96198000901)

WHEELS / DECALS

KEY   PART 

NO.    NO. 

DESCRIPTION

  1  196752X421   Wheel Assembly, 16", with Power Steering, LH

  2  155443 

 Pin, Klik  1/4

  3  405161 

 Cover, Power Steering

  4  184471 

 Screw, Shoulder, Hex Head  #10-24 x 1/2

  7  17000616 

 Screw, Hex Head  3/8-16 x 1

  8  185603X479   Bracket, Steering Cable, RH

  9  185602X004   Bracket, Steering Cable, LH

 10  17600406 

 Screw, Cap, Hex Head  5/16-18 x 3/4

 11  17490508 

 Screw, Hex Head  5/16-18 x 1/2

 12  405077 

 Link, Steering Lever

 13  193506X479   Lever Assembly, Steering

 14  182015 

 Pin, Steering Lever

 15  194944X008   Bellcrank

 16  194939X008   Bracket Assembly, LH Steering

 17  194943X008   Bracket Assembly, RH Steering

 18  181847 

 Pin, Steering Bellcrank

 19  85179 

 Retainer, Hairpin

 20  179148X479   Bracket, Lever Assembly

 21  192126 

 Driver, Wheel

 22  182466 

 Ring, Wire Retainer

 23  187622 

 Lobe, Wheel

 24  194941 

 Slide, Clutch

 25  179139 

 Spring, Clutch Slide

 26  194940 

 Lobe, Axle

 27  189282 

 Key, Square  1/4 x 1/4 x 7/8

 28  174697 

 Washer, Thrust (1")

 30  193885 

 Spring, Return, Steering Latch

 31  196753X421   Wheel Assembly, 16", with Power Steering, RH

 32  700279 

 Clip, Retainer

 33  12000045 

 Ring, Retaining

KEY   PART 

NO.    NO. 

DESCRIPTION

 1  181037 

 Decal, Danger

  2  416837 

 Decal, Poulan Pro, 13.0 / 30"

  3  181035 

 Decal, Danger, Deflector

 4  181042 

 Decal, Danger

  5  406989 

 Decal, Poulan Pro

 6  181033 

 Decal, Instruction

  7  415399 

 Decal, LH Trigger

  8  415398 

 Decal, RH Trigger

  9  415475 

 Decal, Speed Control

 10  183730 

 Decal, Remote Deflector

 - - 

416751

 

 Owner’s Manual, English

 - - 

416752

 

 Owner’s Manual, French

NOTE:

  All component dimensions given in U.S. inches.     1 inch = 25.4 mm

IMPORTANT:

  Use only Original Equipment Manufacturer (O.E.M.) replacement parts.

Failure to do so could be hazardous, damage your snow thrower and void your warranty.

Summary of Contents for 416751

































Reviews: