background image

27

KEY   PART 

NO.    NO. 

DESCRIPTION

  1  17490508 

 Screw  1/4-20 x 1/2

 2  187794 

 Spacer, Axle

 3  174697 

 Washer, Thrust

  4  74780632 

 Screw, Cap, Hex Head  3/8-16 x 2

 5  179830 

 Bearing, Axle

  6  73930600 

 Nut, Hex, Centerlock  3/8-16

 7  187776 

 Transmission Assembly

  8  187787 

 Speed Control Arm, Hydro

 9  700279 

 Retainer Clip

 10  188101 

 Torque Strap

 11  193255X479   Bracket, Anti-Rotate

 12  73800400 

 Nut, Hex, Nylock  1/4-20

 13  150078 

 Screw, Hex Washer Head  5/16-18 x 3/4

 14  193256 

 Rod, Bypass Valve

 15  191995 

 Pop Rivet

 16  404308 

 Shaft, Axle

 18  198466 

 Cable, Drive Control

 19  192000 

 Bracket, Cable, Rear

 20  191993 

 Bracket, Cable, Front

 21  87930 

 Clip, Cable

 22  17391208 

 Screw, Slotted Hex Head  1/8 x 1/2

 23  146315 

 Screw, Hex Head  5/16-18 x 3/4

REPAIR PARTS

 

SNOW THROWER - MODEL  

PP13TEPH30

  (96198000901)

DRIVE

NOTE:

  All component dimensions given in U.S. inches.     1 inch = 25.4 mm

IMPORTANT:

  Use only Original Equipment Manufacturer (O.E.M.) replacement parts.

Failure to do so could be hazardous, damage your snow thrower and void your warranty.

Summary of Contents for 416751

































Reviews: