background image

25

KEY   PART 

NO.    NO. 

DESCRIPTION

 1 

402682x479

   Lever, Auger Control, RH

 2 

412681x479

   Lever, Traction Drive Control LH

 4  178888 

 Bushing, Flange

 5  169675 

 Retainer, Hairpin

  6  17060408 

 Screw, Hex Head  1/4-20 x 3/4

  7  412677 

 Bail Control, Interlock

  8  196333X008   Arm, Impeller Rod

 9 

412679x008

   Arm, Traction Rod

 10 

412683x479

  

Panel, 

Control

 11  74780524 

 Screw, Hex Head  5/16-18 x 1-1/2

 12  74780528 

 Screw, Hex Head  5/16-18 x 1-3/4

 13  414519X479   Handle Tube, LH

 14  414518X479   Handle Tube, RH

 15  751153 

 Nut, Lock  5/16-18

 16  19131316 

 Washer, Flat  3/8

 17  178899 

 Knob, Handle

 18  180480 

 Rod, Auger Control

 19  405740 

 Rod, Traction Control

 22  72120618 

 Bolt, Carriage  3/8-16 x 2-1/4

 23  401940X479   Handle Tube, Lower

 24  180447 

 Sleeve, Spring

 25  180926 

 Spring, Traction Drive

 26  178669 

 Spring, Auger Control

 27  17000616 

 Screw, Hex Head  3/8-16 x 1

 28  412680 

 Bushing, Pivot Lever

 30  182906 

 Console, Panel

 31  175262 

 Screw, Hex Head, Tapping  #10-24 x 1-1/4

 32  184471 

 Screw, Hex Head, Tapping  #10-24 x 1/2

 34 

17060410

 

 Screw TA. Semi Gimle 1/4-20 x .62

 36  178831 

 Spring, Torsion, Lever

 37 

412675x004

  

Spring, 

Interlock

 38  180927 

 Headlight, Halogen (Includes Bulb)

  - -  401620 

 Bulb, Halogen

 39  178668 

 Bezel, Headlight

 40  178770 

 Harness, Headlight (Halogen)

 42  414572 

 Cam, Interlock

REPAIR PARTS

 

SNOW THROWER - MODEL  

PP10530ES

  (96192001801)

HANDLES

NOTE:

  All component dimensions given in U.S. inches.     1 inch = 25.4 mm

IMPORTANT:

  Use only Original Equipment Manufacturer (O.E.M.) replacement parts.

Failure to do so could be hazardous, damage your snow thrower and void your warranty.

Summary of Contents for 415244

































Reviews: