11
OPERATION
The operation of any tractor can result in foreign objects thrown into the eyes, which can
result in severe eye damage. Always wear safety glasses or eye shields while operating
your tractor or performing any adjustments or repairs. We recommend a wide vision
safety mask over spectacles or standard safety glasses.
IMPORTANT: LEAVING THE IGNITION SWITCH IN ANY
POSITION OTHER THAN "OFF" WILL CAUSE THE
BATTERY TO BE DISCHARGED, (DEAD).
NOTE: Under certain conditions when tractor is standing idle
with the engine running, hot engine exhaust gases may
cause “browning” of grass. To eliminate this possibility,
always stop engine when stopping tractor on grass areas.
CAUTION: Always stop tractor com-
pletely, as described above, before leav-
ing the operator's position; to empty
grass catcher, etc.
HOW TO USE YOUR TRACTOR
TO SET PARKING BRAKE (See Fig. 5)
Your tractor is equipped with an operator presence sensing
switch. When engine is running, any attempt by the operator
to leave the seat without first setting the parking brake will
shut off the engine.
•
Depress clutch/brake pedal into full “BRAKE” position
and hold.
•
Place parking brake lever in “ENGAGED” position and
release pressure from clutch/brake pedal. Pedal should
remain in “BRAKE” position. Make sure parking brake
will hold tractor secure.
STOPPING (See Fig. 5)
MOWER BLADES -
•
To stop mower blades,move attachment clutch lever to
“DISENGAGED” position.
GROUND DRIVE -
•
To stop ground drive, depress clutch/brake pedal into
full “BRAKE” position.
•
Move motion control lever to neutral (N) position.
IMPORTANT:
THE MOTION CONTROL LEVER DOES
NOT RETURN TO NEUTRAL (N) POSITION WHEN THE
CLUTCH/BRAKE PEDAL IS DEPRESSED.
ENGINE -
•
Move throttle control to slow position.
NOTE: Failure to move throttle control to slow position and
allowing engine to idle before stopping may cause engine to
“backfire”.
•
Turn ignition key to “OFF” position and remove key.
Always remove key when leaving tractor to prevent
unauthorized use.
•
Never use choke to stop engine.
PARKING BRAKE
"ENGAGED"
POSITION
MOTION
CONTROL
LEVER
THROTTLE/CHOKE
CONTROL
IGNITION
KEY
"DISENGAGED"
POSITION
ATTACHMENT CLUTCH
LEVER "ENGAGED"
POSITION
CLUTCH/BRAKE PEDAL
"DRIVE" POSITION
PARKING BRAKE
"DISENGAGED" POSITION
FIG. 5
"BRAKE"
POSITION
TO ADJUST MOWER CUTTING HEIGHT (See
Fig. 5)
The position of the attachment lift lever determines the
cutting height.
•
Grasp lift lever.
•
Press plunger with thumb and move lever to desired
position.
The cutting height range is approximately 1-1/2 to 4". The
heights are measured from the ground to the blade tip with
the engine not running. These heights are approximate and
may vary depending upon soil conditions, height of grass
and types of grass being mowed.
•
The average lawn should be cut to approximately 2-1/2
inches during the cool season and to over 3 inches
during hot months. For healthier and better looking
lawns, mow often and after moderate growth.
•
For best cutting performance, grass over 6 inches in
height should be mowed twice. Make the first cut
relatively high; the second to desired height.
TO USE THROTTLE CONTROL (See Fig. 5)
Always operate engine at full throttle.
•
Operating engine at less than full throttle reduces the
battery charging rate.
•
Full throttle offers the best bagging and mower perfor-
mance.
TO MOVE FORWARD AND BACKWARD (See
Fig. 5)
The direction and speed of movement is controlled by the
motion control lever.
•
Start tractor with motion control lever in neutral (N)
position.
•
Release parking brake and clutch/brake pedal.
•
Slowly move motion control lever to desired position.
