Poulan Pro 172787 Operator'S Manual Download Page 5

5

3 POSITION “QUICK” HANDLES 
•   Raise lower handle section to operating 

position and squeeze the bottom ends 
of lower handle towards each other until 
the pin in handle can be inserted into 
one of the three height adjustment holes.

3 POSITION “EURO” / “EZ” HANDLES 
•   Raise lower handle section to operating 

position and align hole in handle with 
one of three height positioning holes.

•   Insert handle bolt through handle and 

bracket and secure with knob.

•   Repeat for opposite side of handle.

Flanged 
locknut

Wheel 
assembly

Wave
Washers

Axle

LIFT 
UP

Operator presence 
control bar

Mowing 
position

LIFT UP

Lower handle

Upper handle

3 POSITION “EZ”

3 POSITION “QUICK”

Knob

Bolt

Handle 
adjustment 
bracket

Handle 

ad just ment 

brack et

Knob

Bolt

Handle pin

Handle 
ad just ment 
bracket

SQUEEZE

3 POSITION “EURO”

ALL HANDLES 
•   Raise upper handle section into place on 

lower han dle, remove protective padding 
and tighten both handle knobs.

•   Remove handle padding holding opera-

tor pres ence control bar to upper handle.

•   Your lawn mower handle can be ad-

justed for your mowing comfort.  Refer to 
“ADJUST HANDLE” in the Service and 
Adjustments section of this manual.

NOTE

:  For shipping purposes, the rear 

wheels on your lawn mower may not be 
adjusted to the same position as the front 
wheels.  Before operating mower adjust all 
wheels to the same cutting height. 

INSTALL REAR WHEELS
(HIGH WHEEL MOWERS ONLY) 

Some high wheel models require wash ers 
which will be pro vid ed in a parts bag.  If provid-
ed, install washers on the axle fi rst as shown.
•   Install one (1) rear wheel on the axle of 

rear wheel adjuster.

•   Install 3/8-16 locknut and tighten securely.
•   Repeat procedure for other rear wheel.

Summary of Contents for 172787





























Reviews: