Potterton Mersey Super Installation And Service Instructions Manual Download

Page: 1 / 35

INSTALLATION AND SERVICE INSTRUCTIONS

Mersey Super

Gas Fired Water Heater

G.C. NO.52476 38

NON SPOUTED MULTIPOINT MODEL

FOR USE WITH NATURAL GAS

THE GAS SAFETY (INSTALLATION AND USE) REGULATIONS 1984.

"In your own interest, and that of safety, it is law that all gas appliances are installed by

competent persons, in accordance with the above regulations. Failure to install appliances

correctly could lead to prosecution."

Installation must be in accordance with the Building Regulations, Byelaws of the Water

Undertaking, and I.E.E. Wiring Regulations. It should be in accordance also with any

relevant requirements of the Local Gas Region and Local Authority and the relevant

recommendations of the following British Standard Codes of practice: BS 6891, BS

5440:1:2 and BS 5546.

LEAVE THESE INSTRUCTIONS WITH THE USER FOR USE ON FUTURE CALLS

Page 1 of 35

Mersey Super - Installation & Service Instructions

09/12/2009

file://P:\System\DATA\Dx\DS1\installation\2551\I24-2551\I24-2551.htm

Summary of Contents for Mersey Super




































Search results

Summary of Contents for Mersey Super

Reviews:

Related manuals for Mersey Super

Brands by name

Popular brands

Potterton Mersey Super, Installation And Service Instructions Manual

Search results

Summary of Contents for Mersey Super

Reviews:

Related manuals for Mersey Super

Brands by name

Popular brands