manualshive.com logo in svg

POSIFLEX LM-30 Series, User Manual, Page: 5 / 20

Share
Download
POSIFLEX LM-30 Series User Manual Download Page 5

 

 

Installing LM/TM-30XXE/32XXE 

According to the model type of your monitor and terminal, the relevant 

instructions are provided below to help you mount your monitors onto your 

Posiflex terminals. During installation, please ensure the terminal is properly 

turned off and disconnected from the power sources to avoid potential hazards. 

Mounting to HS series Terminals 

1.

 

Lay your POS terminal on a flat surface with 

its rear facing towards you. 

 

2.

 

Press down the release tab of top I/O interface 

cover. 

 

3.

 

Pull the top I/O cover in the direction shown 

by the arrow in the figure to remove the cover. 

 

4.

 

Position the monitor on a flat surface. While 

keeping it steady with one hands, pull the rear 

mounting bracket upright as shown in the 

figure. 

 

5.

 

Support your monitor to align its mounting 

bracket with four screw holes at the back of 

your terminal. Secure the mounting bracket 

with four #6-32-10L fixing screws. 

 

 

 

 

5 

Summary of Contents for LM-30 Series





















Reviews:

No comments