Portland 63190 Owner'S Manual Download

Page: 13 / 16

Page 13

For technical questions, please call 1-800-444-3353.

Item 63190

SAFET

ERA

TION

AINTENAN

SSEM

Sharpening/Replacing Saw chain

1. Have the cutters sharpened by a

qualified technician when:
a.  The sawdust becomes powder-like.
b.  You can’t make the cut without extra force.
c.  The Pole Saw does not cut straight.
d.  Vibration increases.

2. A Saw Chain that is damaged or too worn to be

restored by sharpening will need to be replaced.

Replacing Drive Sprocket

Have the Drive Sprocket replaced by a qualified technician when the Saw Chain is replaced.

Determining Guide bar Wear

The rails of the Guide Bar groove should

always be parallel to each other. Place a

ruler along the side of the Guide Bar and

Saw Chain. If there is a gap, the bar is normal.

Straight

Guide bar

Ruler

Rail

Saw

chain

Gap

If the ruler is flush with the Guide Bar and

Saw Chain, or the Chain tilts to one side, then the

Guide Bar is worn and needs to be replaced.

Ruler

Worn

Guide bar

Tilting Saw

chain

Summary of Contents for 63190

















Search results

Summary of Contents for 63190

Reviews:

Related manuals for 63190

Brands by name

Popular brands

Portland 63190, Owner'S Manual

Search results

Summary of Contents for 63190

Reviews:

Related manuals for 63190

Brands by name

Popular brands